My wifes mini on homemade Rotisserie

C

coxyboys

Member

Messages

12

• Dec 31, 2011

• #1

Hi there just a few pics of ongoing mini project on Rotisserie/Spit I made last year.
The Spit is adjustable for height and centre of mass to make spinning car easy and safe. I am not good at getting under cars anymore so this make it a lot easier.
I dont get to the computer that often but will reply to messages as soon as I can.
I dont know if this has been posted in the correct place if not I am sorry and would it be possible to move it to the right one

Rotisserie was based on this link

http://www.harwoodperformance.bizland.com/1941buick/Editorial_20.htm

Cheers for now

 

• 
  Rotisseriefront.jpg

  111 KB · Views: 1,984
• 
  Rotisserie1front.jpg

  126.1 KB · Views: 2,002
• 
  DSC_0018-1.jpg

  75.3 KB · Views: 2,016
• 
  Rotisserierear.jpg

  126.4 KB · Views: 1,973
• 
  DSC_0064.jpg

  80.5 KB · Views: 1,955
• 
  DSC_0068.jpg

  71.3 KB · Views: 1,951
• 
  DSC_0081.jpg

  62.8 KB · Views: 1,943
• 
  DSC_0082.jpg

  71.5 KB · Views: 1,963
• 
  DSC_0083.jpg

  59.6 KB · Views: 1,958
• 
  DSC_0087.jpg

  64.3 KB · Views: 1,950
• 
  DSC_0101.jpg

  63.2 KB · Views: 1,942

T

troppo

Member

Messages

485

• Dec 31, 2011

• #2

Sweet Rotisserie mate, looks like the perfect adjustable design

 

P

philsmin

Member

Messages

221

• Jan 1, 2012

• #3

Makes it all so much easier, best thing I did when I restored my mini shell.

Mine was a bit more bodged together than that, I had some old tube lying around so made it out of that!

What engine you going to be running, that aint no mini subframe

 

M

Minimad30

New Member

Messages

1

• Jan 3, 2012

• #4

Hmm engine mounts suggest a vaux or Suzuki/Micra, I'm doing a Honda mini at the moment. Just got my tig to start modifying the inlet to clear the bulkhead! Rotisserie looks very handy!!

 

C

coxyboys

Member

Messages

12

• Jan 4, 2012

• #5

Cheers guys am fitting a small block vauxhall engine 1400 to keep in the low tax bracket. 5 speed box and 5 main bearing crank is so much better than mini engine. Its a shame because I love mini engines but there are better units out there now. Going to run on carb again to keep it simple.
Rotisserie allows me to adjust the centre of balance so car can be rotated with one hand , may modify the horizontal mounts that go to the chassis as at the moment they can twist slightly with the weight of the car.
will post a few more close ups of the rotisserie when I can

Cheers

 

• 
  DSC_0118.jpg

  48.8 KB · Views: 1,758
• 
  DSC_0119.jpg

  55.3 KB · Views: 1,528
• 
  DSC_0113-1.jpg

  36.6 KB · Views: 1,523
• 
  DSC_0114-1.jpg

  51.6 KB · Views: 1,510
• 
  DSC_0120.jpg

  44.9 KB · Views: 1,497
• 
  DSC_0122.jpg

  46.6 KB · Views: 1,512

D

DuncanCallum

Lots more enthusiasm than skill....

Messages

93

Location

Uk

• Jan 7, 2012

• #6

that's one hefty frame mount.

I like it, How have you jigged it up to get the location right?

 

D

Delta

pre-moderated

Messages

127

• Jan 7, 2012

• #7

'Rotisserie' !

You is like well posh innit m8!

Delta.
(Owner of a Northern 'Spit')

 

C

coxyboys

Member

Messages

12

• Jan 9, 2012

• #8

Delta said:

'Rotisserie' !

You is like well posh innit m8!

Delta.
(Owner of a Northern 'Spit')

Click to expand...

I needed a good laugh this morning Cheers for that , If you saw a pic of me you would not call me posh !

 

stuvy

Member

Messages

9,304

• Jan 9, 2012

• #9

just out of interest, do people stick 1.4zetec ford engines into mini's? they have a load more oomph than vhall ones

 

C

coxyboys

Member

Messages

12

• Jan 9, 2012

• #10

DuncanCallum said:

that's one hefty frame mount.

I like it, How have you jigged it up to get the location right?

Click to expand...

I made a pattern of the end of the original heel board from sheet steel with 5/16 holes drilled where the original mounts were extending the pattern inward towards centre of the car .
I then bolted pattern to mounting holes. Then drilled two holes through the pattern into the heel board so it could be riveted in place later.
I will post pics when I have taken some

Cheers for now

 

C

coxyboys

Member

Messages

12

• Jan 9, 2012

• #11

stuvy said:

just out of interest, do people stick 1.4zetec ford engines into mini's? they have a load more oomph than vhall ones

Click to expand...

Not that I know of I think it has something to do with the location of drive shafts but do not quote me !

 

stuvy

Member

Messages

9,304

• Jan 9, 2012

• #12

just wandered thats all, those se or zetec lumps rev stupidly high. Iv been in a mates 1.25 zetec fiesta with a hot cam kit, exhaust and panel filter and it kept up with a 1.8 new shape celica. his fiesta revved to 7000rpm!

 

P

philsmin

Member

Messages

221

• Jan 9, 2012

• #13

Pretty sure the Zetec is too tall, it's also quite a big engine and heavy engine compared to the vaux lumps.

 

stuvy

Member

Messages

9,304

• Jan 9, 2012

• #14

just wandered thats all

 

C

coxyboys

Member

Messages

12

• Jan 10, 2012

• #15

DuncanCallum said:

that's one hefty frame mount.

I like it, How have you jigged it up to get the location right?

Click to expand...

Some pics of the heel board pattern

 

• 
  DSC_0144.jpg

  59.8 KB · Views: 422
• 
  DSC_0145.jpg

  56.1 KB · Views: 428