Help me find something

[Jaffman]

Hi, I need some assistance from an engineering hive mind.

I need a ball joint/rod end that has a boot over the ball, and a hex on the ball to be able to turn the threaded end into a fixture.
the thread needs to be m12x1.75 and the female thread that goes on the rod needs to be m14x1.5

something like this...

Rod End Sq LHS12-IKO 12mm.

<p><span>The Rod End Sq known as LHS12-IKO IKO has an inner diameter of 12 mm.</span></p>

www.123bearing.co.uk

but with the above measurments.

anyone know of anywhere I can get something like this from?

TIA

 

[carbon]

McGill motorsports do some but they are mostly unf. They do have some metric

Rod ends

 

[Jaffman]

That’s great thanks!
So help me understand..

This one… https://www.mcgillmotorsport.com/m12-x-1.25mm-male-female-ball-joint-/-track-rod-end-c-89-p-337

Is m12 on both threads?

Next question is best way to change an m12x1.75 to an m12x1.25

 

[Agroshield]

This one:

IKO - LHSA12 - Rod end - L-Ball Rod end

Buy LHSA12. We stock large numbers of rod ends with female thread with same day dispatch and worldwide distribution.

www.acorn-ind.co.uk

a 12.5mm drill bit and an M14 x 1.5 tap.

 

[jsf55]

https://www.mcgillmotorsport.com/m1...x1.5-ultra-high-performance-rod-end-c-4-p-287 + https://www.mcgillmotorsport.com/m14-rod-end-misalignment-spacers-14mm-pack-of-4-c-94-p-581 +

RODOBAL Rubber Dust Protection Sealing Boot for 3/8" 7/16" & 1/2" M10, M12, M14 Rose Joints

RODOBAL offer high quality items, we offer them at the lowest prices around.

www.mcgillmotorsport.com

Is how i did my track rod ends on my pop, just use a 14mm hi tensile bolt through the assembly with a lock nut
EDIT cap screw to take the dust cover

 

[Jaffman]

This one:

IKO - LHSA12 - Rod end - L-Ball Rod end

Buy LHSA12. We stock large numbers of rod ends with female thread with same day dispatch and worldwide distribution.

www.acorn-ind.co.uk

a 12.5mm drill bit and an M14 x 1.5 tap.

They look perfect!

 

[Jaffman]

https://www.mcgillmotorsport.com/m1...x1.5-ultra-high-performance-rod-end-c-4-p-287 + https://www.mcgillmotorsport.com/m14-rod-end-misalignment-spacers-14mm-pack-of-4-c-94-p-581 +

RODOBAL Rubber Dust Protection Sealing Boot for 3/8" 7/16" & 1/2" M10, M12, M14 Rose Joints

RODOBAL offer high quality items, we offer them at the lowest prices around.

www.mcgillmotorsport.com

Is how i did my track rod ends on my pop, just use a 14mm hi tensile bolt through the assembly with a lock nut
EDIT cap screw to take the dust cover

Yeah that was the original plan as I currently have a rose joint. But I’m not convinced with that boot personally and with me redoing the outer joints I thought I’d try and find something that fits from the off instead of making something fit

 

[jsf55]

Done 15000 miles in mine and just a check over in the winter and a bit more grease does the trick

 

[northwest]

I don't quite get what you are looking for, you buy the boots seperately and they are pretty much universal, The hex bit is not needed, you just put an adjustable across the flats to turn it.

thread needs to be m12x1.75 and the female thread that goes on the rod needs to be m14x1.5

You quite simply put a bolt through the rod end, this can be any pitch you want. Try here:

Search Results: rod ends - Simply Bearings Ltd

simplybearings.co.uk

I GET IT NOW,you are looking for TRACK ROD ENDS. I on the other hand, have bearings on the brain so the obvious solution from me is a Rose Joint!!!!

 

[Agroshield]

You quite simply put a bolt through the rod end, this can be any pitch you want.

Would that not lead to a sloppy fit as the shank diameter of an M12 bolt, for example, is slightly smaller than 12mm? You would also have issues with thread length - using a setscrew would be worse as the major dia. of the threads is smaller than that of the shank. A shoulder bolt would provide the correct fit, but none are made with a short enough shoulder to suit a rose joint.

 

[Jaffman]

Would that not lead to a sloppy fit as the shank diameter of an M12 bolt, for example, is slightly smaller than 12mm? You would also have issues with thread length - using a setscrew would be worse as the major dia. of the threads is smaller than that of the shank. A shoulder bolt would provide the correct fit, but none are made with a short enough shoulder to suit a rose joint.

its what i currently have now, but the setup I have means I have to take the rosejoint off to adjust the toe of the wheel. so im redoing the setup I have and if im redoing it I would rather have a traditional style ball joint instead of a rose joint. (ive already lost the inserts on them so id rather it all be contained)

but because I have a threaded fit into my hubs instead of a tapered shaft like a normal tie rod end I needed one with the hex on the end to drive it into the hub.

ive bought the ones linked above for now anyway so we will see how that goes. im not worried about the size of the female thread too much as I need to made an adaptor anyway.