Makita MM4 engine

[MattF]

That's pretty much what I did. Looking at photo's isn't like having them there in the flesh though. Having some carbs knocking about is no bad thing either.

I'm wanting to get it sorted this week as I'm on holiday, so have the time to sort it.

 

[MattF]

Is it feasible to run a 4 stroke on a 2 stroke mix for a short while?

 

[angellonewolf]

Is it feasible to run a 4 stroke on a 2 stroke mix for a short while

i would think the bottem of the engine would still need its oil to the right level as i would assume there is a pump unless its a splash type engine

and dont 2 strokes need compression in the whole piston chamber thats why they oil in the fuel

 

[MattF]

Sump is at level too. Didn't end up needing to resorting to 2 stroke. Dad had a bit of petrol at his.

I now have a properly working backpack blower. Can whack it upto full throttle without issue now. Even the throttle control cover from the original fits the new carb.

Used this carb:

1PZ UK5-11C 11mm Carburettor Carb Replacement https://amzn.eu/d/08MzQO8

One had a larger port on the engine side, so dismissed that one. The other is very similar to the above, but the gasket hole was misplaced, so just went with the one which was a straight swap with no faffing.

Throttle assembly cover on the new carb:



Plus, I now have a fuel adjustment screw, if I need to tweak it.

Goes to show they're basically using a generic carb, with slight alterations.

 

[MattF]

Thanks for all your help with this chaps. Appreciated.

 

[angellonewolf]

Sump is at level too. Didn't end up need to resorting to 2 stroke. Dad had a bit of petrol at his.

I now have a properly working backpack blower. Can whack it upto full throttle without issue now. Even the throttle control cover from the original fits the new carb.

Used this carb:

1PZ UK5-11C 11mm Carburettor Carb Replacement https://amzn.eu/d/08MzQO8

One had a larger port on the engine side, so dismissed that one. The other is very similar to the above, but the gasket hole was misplaced, so just went with the one which was a straight swap with no faffing.

Throttle assembly cover on the new carb:

View attachment 415966

Plus, I now have a fuel adjustment screw, if I need to tweak it.

Goes to show they're basically using a generic carb, with slight alterations.

and buy another for next time bag it and put makita blower on it so you know its the right one

 

[MattF]

and buy another for next time bag it and put makita blower on it so you know its the right one

One of the others I ordered will fit too, so already got a spare, but I think I'll get another of the above too, as then I've got some more fuel line & another filter too. This one is the other:

QWORK® Carburetor 22cc 26cc 33cc 34cc 36cc https://amzn.eu/d/aZl5ns3

Going to see if I can swap the blanking plate from the old carb to that one, to get rid of the unnecessary primer bulb on the carb.

 

[MattF]

Given it a proper test today. Running like a dream now. So nice to have it working properly again. It's spent more time sickly than well, since I've had it.

Thanks again chaps.

I've swapped the blanking plate over to one of the other carbs, & ordered another of the carbs it currently has fitted, just incase.

 

[RonMig]

Looks pretty much like the same carb as I fixed for my brother, on his strimmer, but upside-down.
The adjuster is hidden under a rubber plug, inside the throttle pivot.
(the brass item which the throttle cable leads to, in this pic)...

opening the throttle pivots a cam and lifts the main jet

The other adjuster was locked-off to be tamper-proof (but can be removed).
I had planned to buy a £15 carb to fix it too, but once I'd got the two adjusters useable, and cleaned out the carb, it ran perfick

 

[MattF]

Seems to be my week for repairing gardening tools. Ordered a new fuel cap for the strimmer last week, (Hyundai, so typical import fare). Fitted it, tried the strimmer, no movement at the spool end. Bearings had seized on the clutch housing. I've just soaked them & worked them loose. Now up & running. Bearings may go completely at some point. Looked at the cost of a bellhousing/clutch, & it's not worthwhile ordering & swapping bearings. Under £30 for a new unit. This's the unit.

 

[MattF]

That cheap carb seems to be more reliable than the OEM one. Fired it up today, for the first time in a few month. Half tank of fuel still in from when I last used it. Half expected similar symptoms, but it ran like a champ.