Today I acquired...........

[Mick Annick]

The top two curved slashers were used around the farm in the 1950's to chop nettles , thistles , brambles & gorse etc. & drag the cuttings to one side

Look like Morris of Dunsford, not bad tools, I have a few of theirs, including the top one

 

[brightspark]

I have the second one up. john bull great for slashing brambles and crappy hedge branches / paid 8 quid for it

 

[Chillitt]

Usually to get the flywheels off use a big quality make three legged puller , undo the holding nut so it just forms a cup on the thread and put the centre bolt of the puller in the middle , use washers if needed to keep it central then tighten it up and once it's tight give the bolt head one sharp slap with a 2 pound hammer .
If it hasn't come off put a lit 100 watt light bulb next to the flywheel n & cover it with a big carboard box so the 100 watts of heat can warm the flywheel through over a few hours of heating then repeat the removal exercise . If it does not budge give it WD 40 let it cool over night then rewarm as before & repeat the exercise .

If you're worried about damaging the crankshaft thread end turn up a small brass boss that sits inside the slackened nut thread then set up the puller as before ,

The flywheel is also the shredder, maybe 14-16 inches across. Id have to drop in in the forge all day to get any heat into it, and the puller would need to be immense. Its one of these

 

[DAPPH]

If it is unbolted at the housing are there any thread extraction holes in the flywheel close to the crank bearing if so see if you can see where they will be pressing h extraction bolt onthe casing .slacken the securing nut a 2 full turns , sometimes you have to rotate the flywheel to align the extraction bolts with thickened jacking pads if there is set all the extractor bolts to the same feeler blade gap & then in cross diagonal selection give each bolt 1/6 of a turn till it is tight with an equal number of flats turned on each bolt . Then with a hard wooden dowel such as a bit of wooden broom shaft or a soft brass / copper / aluminium drift , put it on the end of the crank shaft and wallop it with a 2 pound hammer try to tighten each extraction bolt another flat and repeat the shock treatment . try it several times but don't strip the threads of the holes or on the bolts .
What I said about heating with a 100 watt lit bulb still stands , once the thing is stripped for access.

 

[Kayos]

Another toy for the collection.
View attachment 248145

Looper with a digital synth engine built in.
Loops external sources too. Should be handy

Still learning so here's someone who knows how to use it

Kaos pad is where my name comes from, I had one and a mini I used to use when I was DJ'ing a very long time ago

 

[steviec_lj]

Kaos pad is where my name comes from, I had one and a mini I used to use when I was DJ'ing a very long time ago

Used to use 4 of the Edirol PCR50 and a V4 for visuals at various events. Got involved with the wife and “had” to give it all up..

 

[Gragson]

And testing.
Name that tune

Sounds like escape from new york from that carpenter film?

You really won't regret the lessons, there is a guy I know who the kids went through and apart from being an amazing pianist and teacher is massively into keyboards and has written published books on learning on keyboards - KeyQuest Music.

What you might find frustrating when the boys learn is how fast they overtake you reading music let alone playing, I got to grade 3 reading just on treble clef playing guitar, they shot to grade 8 exams with distinctions in no time. If you can sit down and play an instrument half well anywhere - you're everybody's friend ut only the very luck make a living out of it...

 

[slim_boy_fat]

Mr Vark, make sure you clean out the tank on the weed burner, rust and bits of paint clog the burner tube if you don't and you end up with a very poor flame.

I beg to disagree - check the pic in my post # 24324

 

[eLuSiVeMiTe]

Sounds like escape from new york from that carpenter film?

You really won't regret the lessons, there is a guy I know who the kids went through and apart from being an amazing pianist and teacher is massively into keyboards and has written published books on learning on keyboards - KeyQuest Music.

What you might find frustrating when the boys learn is how fast they overtake you reading music let alone playing, I got to grade 3 reading just on treble clef playing guitar, they shot to grade 8 exams with distinctions in no time. If you can sit down and play an instrument half well anywhere - you're everybody's friend ut only the very luck make a living out of it...

Been wanting to for over a decade but never seem to make time. I will this time so I can work with the boys. Whenever they hear the gear fire up there all there like a shot to play

Re the tune

And for comparison

Needs a little more growl but very close
@Maker got it first time with a cryptic answer


I'll normally play with all my fingers but this riff was alien and had to slow it down initially. Got it well memorised now

 

[eLuSiVeMiTe]

Kaos pad is where my name comes from, I had one and a mini I used to use when I was DJ'ing a very long time ago

Now I've cancelled an eBay order for a kaos mini and kaosilator mini il pull the trigger on a kaos pad 3. Very very useful

Got it set now so sending a track to a mixer buss sends it to the kaosilator for loop recording. Did you ever crack the 303 out?

 

[slim_boy_fat]

If you can sit down and play an instrument half well anywhere - you're everybody's friend

Just don't take your harp to a party....

You might prefer Gracie Field's version , also available on the 'Tube.

 

[JEZGUZ]

If you are brave enough to remove the jet while it is burning then you will get a big flame, but it empties the tank a bit quickly and the neighbours start ducking

 

[slim_boy_fat]

Been wanting to for over a decade but never seem to make time. I will this time so I can work with the boys. Whenever they hear the gear fire up there all there like a shot to play

Re the tune

And for comparison

Needs a little more growl but very close
@Maker got it first time with a cryptic answer


I'll normally play with all my fingers but this riff was alien and had to slow it down initially. Got it well memorised now

I've been trying at every episode to identify the tune, your expertise/skills with music just pushed to to delve deep into Google...

When I saw 'Da Funk' I thought we were going to get this from Project Binky - who knew Brian May played in Extreme?

Based [allegedly] melody-wise[?]on Mark Ronson's 'Uptown Funk'

I've been trying at every episode to identify the music and your posts about your musical skills just gave me the push needed to delve into and spend waste time on Google.

 

[slim_boy_fat]

If you are brave enough to remove the jet while it is burning then you will get a big flame, but it empties the tank a bit quickly and the neighbours start ducking

Not brave enough in those days to mess with the thing , I just filled it up with the 'burny' stuff, pressurised it and that was what I got...... As I said, no instructions etc from the hire place...maybe I didn't look stupid back in the day.

I suspect lack of checking/servicing before I picked it up - who'd know what the previous customer did with/to it? I DID learn a valuable lesson though, so it wasn't a total loss as an exercise.

 

[bigegg]

A set of clay modelling tools.
£21 from the bay.
Not the best quality, but there doesn't seem to be a middle ground: its either cheap'n'nasty or

"How much!!!!"

These will get me started until i know the actual tools I need.

 

[Chillitt]

Torque.
https://play.google.com/store/apps/details?id=org.prowl.torquefree&hl=en_GB

Another one although I haven't tried it is Dashcommand.
https://play.google.com/store/apps/details?id=com.palmerperformance.DashCommand&hl=en_GB

Torques done 'something' as it will now start, but wont help with the service light or abs or airbag light... Dash command doesnt seem to work at all....

 

[Arc Tourist]

Got a used "Tama" brand joggler/punch from an ebay seller today.
.

 

[snoozer]

Torques done 'something' as it will now start, but wont help with the service light or abs or airbag light... Dash command doesnt seem to work at all....

It's a bit of a mine field with code readers if they'll work with different software's, tbh my primary use is with Customers Motorcycles and I got the OBDLINK LX on recommendation in the trade and I use it with Tune ECU & MotoScan.
I down loaded Torque to have a play with my Pug 407 again it was recommended as I don't have much experience with Cars and ODB.
What Car are you playing with and what reader out of interest ?
I also use a decent adapter lead when plugging into to the BMW 10 pin Diag port, Used cheap and they've let me down.

 

[Chillitt]

It's a bit of a mine field with code readers if they'll work with different software's, tbh my primary use is with Customers Motorcycles and I got the OBDLINK LX on recommendation in the trade and I use it with Tune ECU & MotoScan.
I down loaded Torque to have a play with my Pug 407 again it was recommended as I don't have much experience with Cars and ODB.
What Car are you playing with and what reader out of interest ?
I also use a decent adapter lead when plugging into to the BMW 10 pin Diag port, Used cheap and they've let me down.

went cheap and got a bluetooth reader for a tenner.. Its an 04 diesel Corsa van. Nice little van, but needs an MOT so hoping it will tell me what it thinks is wrong with it rather than having to physically find a fault. (If there is one...) htt[URL]https://www.ebay.co.uk/itm/283711438998 [/URL] and a Samsung phone

 

[Kayos]

went cheap and got a bluetooth reader for a tenner.. Its an 04 diesel Corsa van. Nice little van, but needs an MOT so hoping it will tell me what it thinks is wrong with it rather than having to physically find a fault. (If there is one...) htthttps://www.ebay.co.uk/itm/283711438998 and a Samsung phone

Im currently having issues with a usb obd reader but for a vauxhall of that age you want opcom, can do 90% of what a tech2 can do and the 10% you will probably never need