What’s with the curved cladding rails?
- Thread starter monkeymark
- Start date
DAPPH
as dyslexik as I'm daft
- Messages
- 7,011
- Location
- Near to Cross Hands Llanelli SouthWales GB
Check for post codes or serial numbers to ensure they are not stolen.. I can't go back to a certain EU country I got caught at pistol point riding a stolen cycle that I'd taken out of the scrap metal skip at work & did it up to full legal spec. The court case appointment arrived at the unit four days after I'd left for N Ireland .
I know the guy who binned them, they were brand new to him last year. (Halfords best)
brightspark
Member
- Messages
- 40,153
- Location
- yarm stockton on tees
probably made by bahco sandvic and badged for brittol
Robert.
Member
- Messages
- 186
- Location
- South East
Cheap crap shed ..the doors have been a nightmare from day one lol
I see your steel stocks gone the same way.
.
Robert.
Member
- Messages
- 186
- Location
- South East
I see your steel stocks gone the same way.
I don't really hold a steel stock as such , the racks just keeps a few bits and bobs ,mostly offcuts and a few cutting edges commonly used . I order as required for projects , next day delivery makes holding costly stock redundant .
I acquired the realisation I'm an idiot.
Needed to get a boring bar setup in the new CNC lathe. Thought I'd take the solid carbide one out the old lathe, so ordered a 10mm boring bar sleeve, and since I had a quad turn bought on offer a while back, I'd get a sleeve for it as well, so ordered a 12mm sleeve.
Turns out the boring bar is an 8mm, and the quad turn that I thought was a 10mm and needed a 12mm sleeve, is actually a 12mm that needs a 16mm sleeve.
So I think I've covered every combination, except one that will work
For the amusement of @Tangledfeet , I shall just requote myself, and reconfirm, I am an idiot
I should really start reading my notes when ordering, to try and avoid ordering the exact same wrong thing twice
On the plus side, I did get one sleeve right, and quad turn tools are pretty good, although I could really do with a longer opposite handed one, as I'm having to run this one hanging out the holder and only held with a single bolt to avoid tool/chuck collisions
Dieselman 63
Forklift Certified
- Messages
- 5,681
- Location
- Wellington, New Zealand
Good luck with the old NEC projector, they were well regarded in their day but that was about ten years ago, unfortunately a new lamp will cost you twice the price of the projector.
There was a time when I could have had any number of used projectors as we replaced and upgraded them for customers, I ended up giving them away to local artists / community groups but don't bother now, just send them for WEEE these days.
Im an artist and that’s what I want it for, projecting images. When it packs in I’ll buy another.
Tangledfeet
Think outside, no box required.
- Messages
- 3,111
- Location
- Top of a hill above St Andrews, Fife
For the amusement of @Tangledfeet , I shall just requote myself, and reconfirm, I am an idiot
I should really start reading my notes when ordering, to try and avoid ordering the exact same wrong thing twice
On the plus side, I did get one sleeve right, and quad turn tools are pretty good, although I could really do with a longer opposite handed one, as I'm having to run this one hanging out the holder and only held with a single bolt to avoid tool/chuck collisions
View attachment 253364
With the complexity of the stuff you're ordering these days I think the odd mistake is more than acceptable!
Maker
Most folk just call me; Orange Joe
- Messages
- 10,487
- Location
- Don't ask questions
Lent this to a friend while I went home for summer, her mum saw it and gave her a spare bottle 1L bottle. A bottle isn't much use without a head so when I went to get my whipper back she gave me the bottle, I didn't tell her I had a spare head.A stainless ISI cream whipper (With a spare head for some reason).
View attachment 238104
Will need to figure out how they come apart, probably give them a dunk in the ultrasound and replace the seals too.
Unfortunately it's alu rather than stainless so nothing hot and nothing acidic (I was hoping to do nitro coldbrew in it) but it'll be good if I ever need loads of cream.
Notice I still need to buy a new nozzle, I had thought my friend would buy a new one in order to use it but clearly she's just been filling balloons all summer. 
rtcosic
Member
- Messages
- 2,725
- Location
- Warwickshire
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,605
- Location
- Going Away.
We all do.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,605
- Location
- Going Away.
I got a thing.
A Brass thing, a brass pumping thing.
Oh yes some steel bits.
A few hours off cleaning it up and finding out what it does.
A Brass thing, a brass pumping thing.
Oh yes some steel bits.
A few hours off cleaning it up and finding out what it does.
slim_boy_fat
Forum Supporter
- Messages
- 29,540
- Location
- Scottish Highlands
Too easy - it's a vintage stirrup pump, innit 
As per.....https://www.worthpoint.com/worthopedia/vintage-brass-stirup-pump-murphex-423373716
As per.....https://www.worthpoint.com/worthopedia/vintage-brass-stirup-pump-murphex-423373716
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,605
- Location
- Going Away.
Too easy - it's a vintage stirrup pump, innit
As per.....https://www.worthpoint.com/worthopedia/vintage-brass-stirup-pump-murphex-423373716
No it is not listed correctly
So pffffts
Rannsachair
Forum Supporter
- Messages
- 3,967
- Location
- Lochgilphead, Argyll, Republic of Scotland
A nice wee eclipse vice to use on my centec:
Perfect size to clamp to bed.
Not bad for £25 I think.
Perfect size to clamp to bed.
Not bad for £25 I think.
