not done it yet
Member
- Messages
- 2,604
- Location
- Lincs/cambs/Rutland/Northants
3kW is 3kW however one looks at it. That 3kW will be converted to thermal energy, one way or another.
- Thread starter hollow
- Start date
3kW is 3kW however one looks at it. That 3kW will be converted to thermal energy, one way or another.
roof insulated but 70s single skin cladding and big , a nightmare, was running to day
dieselsamurai
Too many projects not enough time!
- Messages
- 1,204
- Location
- Hampshire
not sure why but i have never suffered condensation in my workshop its standalone at the bottom of the garden tin roof but insulation then ply wood under that ontop of wooden joists , deos the amount of wood surface area you have make any difference?
It was 0 degrees the other day but 8 inside and i rarely heat it , the only thing it could be is the floor is about 8 or 9 inches of concrete maybe that keeps the heat in ?
It was 0 degrees the other day but 8 inside and i rarely heat it , the only thing it could be is the floor is about 8 or 9 inches of concrete maybe that keeps the heat in ?
MattF
Forum Supporter
- Messages
- 16,791
- Location
- South Yorkshire
Mine's a compressor type, so some additional heating is necessary this time of year. Have considered getting a dessicant type for the workshop, but still undecided.
Smouser
Member
- Messages
- 1,074
- Location
- Amesbury, Wiltshire, UK
I was away yesterday and did not get a chance to cover all my machines in oil before the weather warmed up.
Opened the garage this morning expecting a bit of condensation.
Well, I got more than I bargained for
I will have to get the fan running, dry, clean and oil everything.
Opened the garage this morning expecting a bit of condensation.
Well, I got more than I bargained for
I will have to get the fan running, dry, clean and oil everything.
It has been just the "perfect storm" for condensation on large lumps of workshop metal.
I did mention that I was preparing for it on Friday:
Wonder if anyone else did the same.
Mind you, the dehumidifier started playing up. The compressor wouldn't run, making repeated attempts to start. The relative humidity slowly climbed ominously upwards. The problem turned out to be the motor starter contacts, which showed signs of possibly being worn or dirty. A shot of switch cleaner, followed by a blast with an air duster seems to have done the trick. The workshop warming beforehand seems to have helped.
I did mention that I was preparing for it on Friday:
Damn this weather...
After the freeze of the washing machine/boiler condensate line I thought we’de Got off lightly with the cold snap. Tonight after the footy I ventured into the workshop, which is really two long garages joined side by side. The issue being “joined”. The roofs are pitched corrugated asbestos...
www.mig-welding.co.uk
Mind you, the dehumidifier started playing up. The compressor wouldn't run, making repeated attempts to start. The relative humidity slowly climbed ominously upwards. The problem turned out to be the motor starter contacts, which showed signs of possibly being worn or dirty. A shot of switch cleaner, followed by a blast with an air duster seems to have done the trick. The workshop warming beforehand seems to have helped.
MattF
Forum Supporter
- Messages
- 16,791
- Location
- South Yorkshire
I set mine on 65%. I've found that to be the best compromise. My **** would be pinching if I saw that % on the display.
If it makes you feel any better, mine is just as bad. The only thing that seems to have escaped is the surface grinder as I keep it soooooo well wrapped up when it's not in use.I was away yesterday and did not get a chance to cover all my machines in oil before the weather warmed up.
Opened the garage this morning expecting a bit of condensation.
Well, I got more than I bargained for
View attachment 473710
View attachment 473712
View attachment 473713
View attachment 473714
View attachment 473716
View attachment 473717
View attachment 473718
I will have to get the fan running, dry, clean and oil everything.
MattF
Forum Supporter
- Messages
- 16,791
- Location
- South Yorkshire
This's the setup in mine.
That little oil filled rad is one I bought recently, from B&M. 650W. That's there more to prevent the dehumidifier icing up if temps drop too much. The dehumidifier is the smallest Arete model. Have to empty that every 3 days, approximately.
The first year or so I was here I didn't have a dehumidifier in there. Lesson quickly learnt, it was.
p.s: @Farside, @Gragson: It's not a bleedin' dungeon, nor a house of pain. Feckers.
That little oil filled rad is one I bought recently, from B&M. 650W. That's there more to prevent the dehumidifier icing up if temps drop too much. The dehumidifier is the smallest Arete model. Have to empty that every 3 days, approximately.
The first year or so I was here I didn't have a dehumidifier in there. Lesson quickly learnt, it was.
p.s: @Farside, @Gragson: It's not a bleedin' dungeon, nor a house of pain. Feckers.
Not good, it’s like someone has sprayed a hosepipe in there.
The lathe is usually dripping in oil anyway so it’s made milk
A couple of hours with the heater on has brought the cast stuff up to air temp and stopped new condensation forming.
Some flash rust
Been over everything with a rag and oiled it all up.
The lathe is usually dripping in oil anyway so it’s made milk
A couple of hours with the heater on has brought the cast stuff up to air temp and stopped new condensation forming.
Some flash rust
Been over everything with a rag and oiled it all up.
It looks a bit dark and dingy, just like a dungeon wouldThis's the setup in mine.
View attachment 473747
That little oil filled rad is one I bought recently, from B&M. 650W. That's there more to prevent the dehumidifier icing up if temps drop too much. The dehumidifier is the smallest Arete model. Have to empty that every 3 days, approximately.
The first year or so I was here I didn't have a dehumidifier in there. Lesson quickly learnt, it was.
p.s: @Farside, @Gragson: It's not a bleedin' dungeon, nor a house of pain. Feckers.
MattF
Forum Supporter
- Messages
- 16,791
- Location
- South Yorkshire
Well Mathew De Sade will this tide you over, best I could do.I'm still so waiting for @Wozzaaah to add that "middle finger" smiley.
dobbslc
Member
- Messages
- 12,166
- Location
- Hertfordshire UK
Just been out to mine and it's like someone has hosed it all down in there
I've cleaned and oiled the lathe, bike and chop saw. I didnt even bother avoiding the brakes on the bike this time round.
ACF50 and a dehumidifier on the way soon I think!
Any recommendations for the dehumidifier?
I've cleaned and oiled the lathe, bike and chop saw. I didnt even bother avoiding the brakes on the bike this time round.
ACF50 and a dehumidifier on the way soon I think!
Any recommendations for the dehumidifier?
Craig-SM
Member
- Messages
- 1,813
- Location
- Heckmondwike
I have a big Dri-Eaz Evolution capable of 63L a day but went into the garage yesterday to start transferring tools into the new tool box only to find everything covered in condensation as the temperature had dropped below 0C and frozen the water in the outlet pipe. Back up and running today and it’s quickly drying everything out and luckily had chance to wipe the tools dry as they were transferred.
Luckily all the power tools are in sealed PackOut cases otherwise they may have been damaged as the condensation was that bad.
Luckily all the power tools are in sealed PackOut cases otherwise they may have been damaged as the condensation was that bad.
I put mine on yesterday, a 20 yr old Hotpoint compressor type. By this morning it has filled it's 4 litre container and stopped, so there was a fair bit of moisture in there. Also the garage side floor was soaking where the wind had blown the moisture under the door. So now I have two dehumidifiers and a heater on half heat on in there, and I've stuffed wet sheets along the bottom of the doors.
