redlig
Member
- Messages
- 3,632
- Location
- wiltshire uk
That looks really smart.What kit did you use as I.m just going to start on an XR 200 rebuild ?
- Thread starter qwakers
- Start date
lchris21
Member
- Messages
- 1,962
- Location
- South Wales
just a cheapo electrostatic magic diy gun. picked it up about 15 years ago, think they've improved since then? Like with painting, prep is the key, hence the gassing out in the oven on alloy, and buying quality powder. Its a bit of a faff in a small oven but handy for smaller bits and bobs as your progressing the build.
Used to be the common thing to do but rarely seen now as by drilling a hole in the fork it will fail the annual inspection by the insurance man!
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
This oil pumb came my way the other week.
I knew the washers were dry, I took it apart in the shop.
One of the washers was replaced, the other was reusable, after a dip in groun nut oil.
New seals were made as well, from a thin sheet of rubber.
A good polish and we now have a usable pump.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
I got this Bras Beer keg tap for one reason only.
It was from a local brewery.
Oh dear me, this is not good. I did not say.
So I lashed it in place, then silver soldered it together.
As the metal was a casting it was not a fun fix.
All done, with luck it will go to the local museum.
slim_boy_fat
Forum Supporter
- Messages
- 29,540
- Location
- Scottish Highlands
lchris21
Member
- Messages
- 1,962
- Location
- South Wales
Burning a hole is a failure... drilling is dependent on where it is..no more than a fork width to the centre line from the tip and no more than a 3rd of the width in diameter.
brewdexta
The biggest tool in the box
- Messages
- 5,603
- Location
- UK
I took a closer look at my motely collection of DTIs. First up are this similar pair of plunger DTIs, one was ok, the other didn't return to the same spot when you released the plunger.
Just needed a good clean of the main shaft with a bit of white spirit and a cotton bud. Only one had a seal and that wasn't in place. Both have holes in the back to led carp in, presumably where there used to be a mount.
Both cleaned and working nicely now and new seals on order. I'll blank the holes in the back and use the sleeve on the shaft for holding, for now.
Next up, this pair, I didn't hold much hope for these, the mercer has a bezel missing and isn't happy. The SPi has had a blunt trauma incident.
The mercer has some damage to teeth, not sure you can see it in the pic but a couple of teeth on the wheel are rounded off just near the main shaft. It has many other issues so I think this is fubar,
The SPi is very stiff on the shaft, I think it may have been bent, probably during a fall from a bench. Also the bezel doesn't rotate. It doesn't want to come off easily, I'll give that another go before I declare it dead.
Next up, this Verdict lever DTI. It has no glass and it worked intermittently especially if you changed the direction switch. There's a bit of corrosion in places so thought it would just be dirt.
However the bit of metal near the screwdriver tip was stuck in there. I thought it may be part of the spiral drive but that seems intact so must have worked its way in, I guess there are several ways that it could have entered. I cleaned the gunge out of it and its now working ok. I've ordered a new glass, or at least I hope I have, its a push fit crystal and I've ordered one 0.1mm oversize.
At some point I'll go over and give them a proper clean and oil, I mainly wanted to find out which could be used, which needs to go in the someday pile, and which are knackered.
Just needed a good clean of the main shaft with a bit of white spirit and a cotton bud. Only one had a seal and that wasn't in place. Both have holes in the back to led carp in, presumably where there used to be a mount.
Both cleaned and working nicely now and new seals on order. I'll blank the holes in the back and use the sleeve on the shaft for holding, for now.
Next up, this pair, I didn't hold much hope for these, the mercer has a bezel missing and isn't happy. The SPi has had a blunt trauma incident.
The mercer has some damage to teeth, not sure you can see it in the pic but a couple of teeth on the wheel are rounded off just near the main shaft. It has many other issues so I think this is fubar,
The SPi is very stiff on the shaft, I think it may have been bent, probably during a fall from a bench. Also the bezel doesn't rotate. It doesn't want to come off easily, I'll give that another go before I declare it dead.
Next up, this Verdict lever DTI. It has no glass and it worked intermittently especially if you changed the direction switch. There's a bit of corrosion in places so thought it would just be dirt.
However the bit of metal near the screwdriver tip was stuck in there. I thought it may be part of the spiral drive but that seems intact so must have worked its way in, I guess there are several ways that it could have entered. I cleaned the gunge out of it and its now working ok. I've ordered a new glass, or at least I hope I have, its a push fit crystal and I've ordered one 0.1mm oversize.
At some point I'll go over and give them a proper clean and oil, I mainly wanted to find out which could be used, which needs to go in the someday pile, and which are knackered.
brewdexta
The biggest tool in the box
- Messages
- 5,603
- Location
- UK
I forgot about the other 2 DTI on the other bench, both suffering from sticky shaft syndrome
the top one is a Baty, the lower a no-name DTI, both not returning consistently
Same as before, a quick clean with a cotton bud with a smidgen of white spirit. The no brand DTI had 2 screw missing from the back and the 2 remaining should have been countersunk, I have some M2 screws in the workshop, somewhere......
Not a good idea to have only 2 screws, the back was well distorted letting all sort of crud in
Both now working sweet - I think I have enough plunger type DTI now
I just need to get a few more anvils, Zoro sell them, or I could make a few.
the top one is a Baty, the lower a no-name DTI, both not returning consistently
Same as before, a quick clean with a cotton bud with a smidgen of white spirit. The no brand DTI had 2 screw missing from the back and the 2 remaining should have been countersunk, I have some M2 screws in the workshop, somewhere......
Not a good idea to have only 2 screws, the back was well distorted letting all sort of crud in
Both now working sweet - I think I have enough plunger type DTI now
I just need to get a few more anvils, Zoro sell them, or I could make a few.
Wedg1e
They call me Mr. Bodge-angles
- Messages
- 7,735
- Location
- Teesside, England
I have a double-sided version of that Verdict which is a bit sticky but can I hell figure out how it comes apart. Tried using a sucker to pull the glasses out but to no avail.
@brewdexta "I have some M2 screws in the workshop, somewhere......"
after all the time you spent labeling those drawers I would have thought you would find them easily!
Mine are in the bakki tin labeled "small screws", unfortunately mixed in with all the other small screws!
after all the time you spent labeling those drawers I would have thought you would find them easily!
Mine are in the bakki tin labeled "small screws", unfortunately mixed in with all the other small screws!
brewdexta
The biggest tool in the box
- Messages
- 5,603
- Location
- UK
@brewdexta "I have some M2 screws in the workshop, somewhere......"
after all the time you spent labeling those drawers I would have thought you would find them easily!
Mine are in the bakki tin labeled "small screws", unfortunately mixed in with all the other small screws!
below M5 they are at the mercy of the Raaco drawers
I did find them, but no countersunk ones, now on order......
Wifes watch strap: the little loops that you tuck the end of the strap under had given up the struggle. Two thin O rings fitted by dint of a fanny stretcher over the buckle and the jobs a good 'un'
Always good to demonstrate the multiple uses of having a workshop to the dexter side of the relationship
Always good to demonstrate the multiple uses of having a workshop to the dexter side of the relationship
Just to clarify, you are referring to her as a forensic expert, and not a four legged bovine?Wifes watch strap: the little loops that you tuck the end of the strap under had given up the struggle. Two thin O rings fitted by dint of a fanny stretcher over the buckle and the jobs a good 'un'
Always good to demonstrate the multiple uses of having a workshop to the dexter side of the relationship
That's a Dexta.
brewdexta
The biggest tool in the box
- Messages
- 5,603
- Location
- UK
I just had to look up one of those, never seen one before. From the pics I can't see a way into the mech either.
Pete.
Member
- Messages
- 14,381
- Location
- Kent, UK
Be prepared for that stickyness to return. Maybe not today, maybe not tomorrow....you know the rest
I have a couple of dial gauges that are the same. I stripped and flushed them out with solvent until no dirt or oil (apparently) remans. Satisfied with a job well done I put them away for a month and guess what? Yep, sticky action again.
Nowadays if I want to use those ones for clocking in some rough gear or maybe dialling in the taper on my grinder I just shove a quick blast of brake cleaner up the stem and work it a couple of times. They work OK then at least long enough for me to do the job then I put them away again until next time.
I have a couple of dial gauges that are the same. I stripped and flushed them out with solvent until no dirt or oil (apparently) remans. Satisfied with a job well done I put them away for a month and guess what? Yep, sticky action again.
Nowadays if I want to use those ones for clocking in some rough gear or maybe dialling in the taper on my grinder I just shove a quick blast of brake cleaner up the stem and work it a couple of times. They work OK then at least long enough for me to do the job then I put them away again until next time.
