- Thread starter God mode restorations
- Start date
Tupers
Member
- Messages
- 945
Absolutely not, you can keep the drop bears and man eating spiders to yourself.You should come here and throw **** around.
Just an ‘82 Mayfair but it’ll get a 1275, twin carbs and 10” wheels.
Sergei Slovenija
Member
- Messages
- 1,267
- Location
- Slovenija Ljubljana
Welding as a craft. Sleeve thread 1/8"
100A
100A
AdventuresInMetal
Member
- Messages
- 218
- Location
- North West, England
Had a quick half hour in the workshop and made a start on my exhaust for the diesel heater to go through the workshop wall, nothing special just mild steel tube that was kicking around.
First time doing any exhaust fabrication and quite enjoying it so far, still got loads to do, probably going to paint it black in high temperature paint.
First time doing any exhaust fabrication and quite enjoying it so far, still got loads to do, probably going to paint it black in high temperature paint.
AdventuresInMetal
Member
- Messages
- 218
- Location
- North West, England
Worked on the sleeve to go through the wall and cut a hole into some 316 stainless for a plate to go on the uPVC cladding. I cut the hole with a cutting disc in the die grinder and finished it with a 50mm flap disc, worked out quite well just took about 45 minutes. 
The sleeve will eventually get packed with rockwool insulation and then fire cement on each end.
The sleeve will eventually get packed with rockwool insulation and then fire cement on each end.
Sergei Slovenija
Member
- Messages
- 1,267
- Location
- Slovenija Ljubljana
coaxial pipes can work to supply fresh air to the boiler. The air gap is sufficient for safety. Mesh covers are needed to keep insects out and to center the inner tube.Worked on the sleeve to go through the wall and cut a hole into some 316 stainless for a plate to go on the uPVC cladding. I cut the hole with a cutting disc in the die grinder and finished it with a 50mm flap disc, worked out quite well just took about 45 minutes.
The sleeve will eventually get packed with rockwool insulation and then fire cement on each end.
View attachment 420000
zx9
Forum Supporter
- Messages
- 5,170
- Location
- South East London
Seems there are a lot of folk of a certain age who regularly go on courses, pottery, metal work, wood work etc. not so much because they want to start a new hobby more to keep then occupied and get away from their partner for a couple of days.To be honest I play around with lots of stuff and I would not have a clue where to start making something like that.
Not sure I would pay money to learnbut what he has produced looks well worth the cost.
Blobber
Member
- Messages
- 2,514
- Location
- lincolnshire
Our local independent brewery did a days course on brewing, that was quite refreshing!
Hood
I am obsessed.
- Messages
- 17,308
- Location
- Carnoustie, Scotland
Got the rack plate anodised and etched, also painted the 3D printed clasps and cut the straps and bolted them permanently to the plate.
This was the first time using sulphuric acid when anodising and it went well, voltage was way lower than it would have been with the sodium bisulphate.
All I need to do now, apart from fit to the bike, is find the clips that came with the kriega bag so I can hold the tails tidy when the bag is not in use.
This was the first time using sulphuric acid when anodising and it went well, voltage was way lower than it would have been with the sodium bisulphate.
All I need to do now, apart from fit to the bike, is find the clips that came with the kriega bag so I can hold the tails tidy when the bag is not in use.
Mick Annick
Forum Supporter
- Messages
- 2,618
- Location
- Burgundy, France (450 miles SE of Somerset)
Have you had the con rods and pistons out yet to etch them? 
Hood
I am obsessed.
- Messages
- 17,308
- Location
- Carnoustie, Scotland
Looked everywhere for a double female housing but couldn't find one. Didn't fancy swapping out between bag and straps as that would involve stitching.
I was going to but steel doesn't etch to great with the diode laserHave you had the con rods and pistons out yet to etch them?
Arc Tourist
Member
- Messages
- 4,884
- Location
- Wales
Have a look on the LOMO water sports website, under the heading motorcycle drybags. They sell a set of tiedown straps which come with a pair of double female connectors. The shop is located in Glasgow.
Hood
I am obsessed.
- Messages
- 17,308
- Location
- Carnoustie, Scotland
Different sidelocks I am afraid. That is the big problem, they are all different, some look very close but they are not quite the same.
henry Kadzielski
Member
- Messages
- 1,208
- Location
- Australia Wollongong
^^^^ why get those when you can build them yourself. Countless hours with equipment that most people can't operate or even understand, doing this and not doing work that actually pays the bills
mtt.tr
Member
- Messages
- 8,431
- Location
- Essex/Suffolk border
More worktable progress.
Liberon Dark Oak wax. It's very easy to apply and should hide most oily finger marks. It smells really nice too.
The wax does show up some saw marks. I should have sanded more first.
Plywood sheets arrived nice and early this morning. An opportunity to try out my plunge saw. This pictured set up doesn't actually work. I can't clamp the track very easily so tried clamping some box section behind the track to act as a stop. The box interferes with the motor housing when the saw is plunged. Some lower profile steel strip would have worked but I managed without anyway. The saw coped fine, some more power wouldn't go amiss though.
Two 5' by 4' sheets stacked on top. They aren't screwed down yet. The table is destined for my workshop shed so it will have to come apart soonish and get finished there. I have some work for it in the garage first.
The edges could do with covering, just to stop splintering and catching on clothes. It's not the greatest material for a top, but being effectively one piece over the whole area, it requires the fewest fixings. I considered thick boards and 6" by 2"s etc, but they needed more bolting down and holes to drill. A 6mm steel plate would be just over 100kg and I have a wooden floor to consider. This'll do for now.
I made the frame for this table on the floor. I won’t have to do my next set of benches that way. Result.
Looking forward to tigging on this. There's a smaller 6mm plate on the red workbench that I can use to protect the top when required. I can get my fat legs comfortably under the table when sat on the stool. Feet nicely on the floor for a pedal if needs be. Arms and elbows supported on the table. It will be a nice change to be truly comfortable for once when tigging.
It's supposed to be for laying out, glue-ups, sheet metal work etc, but it will end up being my go to for everything for the time being. A few more benches and I can start tidying up round here.
Liberon Dark Oak wax. It's very easy to apply and should hide most oily finger marks. It smells really nice too.
The wax does show up some saw marks. I should have sanded more first.
Plywood sheets arrived nice and early this morning. An opportunity to try out my plunge saw. This pictured set up doesn't actually work. I can't clamp the track very easily so tried clamping some box section behind the track to act as a stop. The box interferes with the motor housing when the saw is plunged. Some lower profile steel strip would have worked but I managed without anyway. The saw coped fine, some more power wouldn't go amiss though.
Two 5' by 4' sheets stacked on top. They aren't screwed down yet. The table is destined for my workshop shed so it will have to come apart soonish and get finished there. I have some work for it in the garage first.
The edges could do with covering, just to stop splintering and catching on clothes. It's not the greatest material for a top, but being effectively one piece over the whole area, it requires the fewest fixings. I considered thick boards and 6" by 2"s etc, but they needed more bolting down and holes to drill. A 6mm steel plate would be just over 100kg and I have a wooden floor to consider. This'll do for now.
I made the frame for this table on the floor. I won’t have to do my next set of benches that way. Result.
Looking forward to tigging on this. There's a smaller 6mm plate on the red workbench that I can use to protect the top when required. I can get my fat legs comfortably under the table when sat on the stool. Feet nicely on the floor for a pedal if needs be. Arms and elbows supported on the table. It will be a nice change to be truly comfortable for once when tigging.
It's supposed to be for laying out, glue-ups, sheet metal work etc, but it will end up being my go to for everything for the time being. A few more benches and I can start tidying up round here.
Last edited:
