- Thread starter God mode restorations
- Start date
Onoff
In the land of the unfinished project I am King!
- Messages
- 11,713
- Location
- Sevenoaks, UK
Memmeddu
Member
- Messages
- 4,793
- Location
- Italia Sardegna
Are you Italian like me?
Sergei Slovenija
Member
- Messages
- 1,267
- Location
- Slovenija Ljubljana
No, ahah.
But I learned this song by ear in 1991. Daughter of a French mother, Welsh father, and granddaughter of an Italian grandmother. She knew many languages and sang and accompanied perfectly. I liked it and remembered it.
It was very far from Slovenia, 12 time zones.
Memmeddu
Member
- Messages
- 4,793
- Location
- Italia Sardegna
I've said because of the screenshots you've uploaded which have Italian language on the website clickable words like "visualizza profilo" instead of "show profile" etcNo, ahah.
But I learned this song by ear in 1991. Daughter of a French mother, Welsh father, and granddaughter of an Italian grandmother. She knew many languages and sang and accompanied perfectly. I liked it and remembered it.
It was very far from Slovenia, 12 time zones.
Dev
8th generation, Weyland type
- Messages
- 1,277
Made a steering wheel for the toy car. This is MK3 - the last one was too big. Novel thing this time was it was a 2 sided carve, machined one side, flipped then did the other so it’s a single piece instead of 2 halves. Not perfect but successful none the less.
MattF
Forum Supporter
- Messages
- 16,646
- Location
- South Yorkshire
Merely altered, not made. Disliked that bog standard grey junction box they used on the chipper, so replaced it with a smaller, black inline junction box, (& dropped one of the case screws down the blade area whilst I was at it ). Cut the top gland off & capped it with a plastic cap which just happened to be a perfect fit over the stub.
). Cut the top gland off & capped it with a plastic cap which just happened to be a perfect fit over the stub.
Sergei Slovenija
Member
- Messages
- 1,267
- Location
- Slovenija Ljubljana
Italy is nearby, I have traveled around the North many times and further to Normandy and Lucerne. And I search a lot in different languages. If you need to find information in Italy, or a link from an Italian site, then.... The sites remember this and such a screenshot is possible.
I did a motorcycle trip down to Malta, Austria back in I think 2011.Italy is nearby, I have traveled around the North many times and further to Normandy and Lucerne. And I search a lot in different languages. If you need to find information in Italy, or a link from an Italian site, then.... The sites remember this and such a screenshot is possible.
Lake Bled was close enough for a day's ride into Slovenia over the Vrsic Pass.
Beautiful part of the world from what I saw of it
Sergei Slovenija
Member
- Messages
- 1,267
- Location
- Slovenija Ljubljana
Flat earth and endless plains have a bad effect on me. The eye cannot latch on. Mountains and volcanoes are childhood imprinting. And there should be a warm sea nearby.I did a motorcycle trip down to Malta, Austria back in I think 2011.
Lake Bled was close enough for a day's ride into Slovenia over the Vrsic Pass.
Beautiful part of the world from what I saw of it
Memmeddu
Member
- Messages
- 4,793
- Location
- Italia Sardegna
Put a charged battery in my Punto.
Turn on, pump started pumping but at the second click nothing.
Starter motor didn't work.
Turned off everything.
Disconnected the main connector checked continuity between the starter motor and ground my fluke says short circuit.
I'm starting to getting bored.
Tomorrow after work I'll go under the car I'll disconnect the starter motor and run a jumper wire to see what it does.
If it doesn't work I'll ask for a starter motor otherwise I'll keep starting the car with the jumper wire .
I'm tired.
I'm considering to buy a 1992 mini cooper 1.3 IE which I'll convert to bike carbs as soon as possible cause I'm getting sick of electronics on cars
Turn on, pump started pumping but at the second click nothing.
Starter motor didn't work.
Turned off everything.
Disconnected the main connector checked continuity between the starter motor and ground my fluke says short circuit.
I'm starting to getting bored.
Tomorrow after work I'll go under the car I'll disconnect the starter motor and run a jumper wire to see what it does.
If it doesn't work I'll ask for a starter motor otherwise I'll keep starting the car with the jumper wire .
I'm tired.
I'm considering to buy a 1992 mini cooper 1.3 IE which I'll convert to bike carbs as soon as possible cause I'm getting sick of electronics on cars
Melvyn Best
Member
- Messages
- 1,560
- Location
- Cambridge
Possibly but plugs were always the ones recommended by Champion
Olderisbetter
Member
- Messages
- 3,741
- Location
- Wolverhampton
Downloaded from thingyverse and printed in PETG for my cordless dewalt router, it holds the katsu bush guides which were £25 from Amazon not tested yet but seems good.
oldbikedavey
Member
- Messages
- 1,044
- Location
- London, England
Today, I made a rocker arm refacing device for my Black and Decker FE valve refacer.
Only really likely to be used on pre unit BSA B series rockers, but it's there, and it will work once I get the tromboning action sussed out....
Archimedes, you are very sadly missed....
Only really likely to be used on pre unit BSA B series rockers, but it's there, and it will work once I get the tromboning action sussed out....
Archimedes, you are very sadly missed....
Memmeddu
Member
- Messages
- 4,793
- Location
- Italia Sardegna
Disassemble my car again.
Starter motor relay.
The starter motor itself might be fine too but I'm going to buy an used unit at the scrapyard and if the car runs I'll replace it later from under the car without disassemble the intake again and messing with the wire harness further more.
I've done with the car till Saturday.
I can now start part two video of the Husqvarna restoration for YouTube since I've not uploaded anything in two weeks
Starter motor relay.
The starter motor itself might be fine too but I'm going to buy an used unit at the scrapyard and if the car runs I'll replace it later from under the car without disassemble the intake again and messing with the wire harness further more.
I've done with the car till Saturday.
I can now start part two video of the Husqvarna restoration for YouTube since I've not uploaded anything in two weeks
northwest
Searching for the Holy Grail.........
- Messages
- 5,772
- Location
- Manchester UK
My pal came over and between us we managed to run four or five of my new bushing spanners off, bloody FINALLY, one of the most difficult jobs I have done on the machine so far (for lots of reasons other than it's CNC):
The original G code turned out wrenches that were just a little too small for the job, we really invested some time into trying to find out why and came up with a series of wrong conclusions until we got to the bit in Mach 3 that said : Tool Offsets. There were values in there that neither of us had entered and after a wrestling match it appears we won. Harmony (and precision) has been restored.
The original G code turned out wrenches that were just a little too small for the job, we really invested some time into trying to find out why and came up with a series of wrong conclusions until we got to the bit in Mach 3 that said : Tool Offsets. There were values in there that neither of us had entered and after a wrestling match it appears we won. Harmony (and precision) has been restored.
Bullet2012
Member
- Messages
- 4,939
- Location
- 238 855 miles from the moon
Firstly a loaf of bread, 1/3 dark rye 2/3 strong white.
Bullet2012
Member
- Messages
- 4,939
- Location
- 238 855 miles from the moon
Next a space down the side of the garage, previously occupied by the central heating oil tank and brambles.
SWMBO for scale.
SWMBO for scale.
