Stuff you have made today

[dobbslc]

1:100 scale figures for architectural models. Tried this before on an fdm printer and it didn't work very well. Loving the detail on resin printing.

View attachment 469416

Is that Fred Fred Dibnah?

 

[Mart63]

Is that Fred Fred Dibnah?

It's either him or Doubleboost I'm sure.

 

[Morris]

Heater pipes for wifey's Pop.

 

[MysterG]

Thing to mount my tube bender in the vice.
Yep I could only find 3 bolts....

 

[gaz1]

now i dont get an f75 issue i get an f22 fault on the boiler

but my booklet states pressure or pump faulty

i can get the pump to start every now and again but when it tries to restart that f22 soon comes up again

so its either buy a 200.00 pump or buy a 100.00 pump

now there is an or to all of this and most plumbers dont want you to know this

ever think it could be the capacitor at 5.00 for the part itself

now my pump is free spinning the water is crystal clear

ever been ripped off by your plumber when the part could be just 5.00 for it and they want to do a pump change at 200.00

 

[nickk]

For @Kram ,these were dug in today.

 

[leadpig]

got a call from a roofer m8 asking if i could make 3 slate breaks quick as theirs have been knicked
, back off pick up it is then lol

 

[Hood]

Got the engine box finished yesterday, as said centre drain channel is removeable to make engine removal easier, just undo 4 buttonheads. Next job for this boat will be a rudder when the 10mm stainless arrives, already have the shaft machined.

 

[RWD3M]

Thing to mount my tube bender in the vice.
Yep I could only find 3 bolts....

View attachment 469566

What size bolts?

 

[MysterG]

What size bolts?

No idea.
Three from a random box of bolts which fitted.
They were a surprisingly fine thread though.

I have others which will do, but I was eager to test it.

Obviously we all know that it will remain with three bolts forever

 

[gaz1]

Thing to mount my tube bender in the vice.
Yep I could only find 3 bolts....

View attachment 469566

my bender just has a square welded to it underneath and thats adequate enough for the vice to hold it

 

[dieselsamurai]

Almost finished this desk for my son he designed and was meant to help....

made from 6 old scaffold boards sawn in half planned down and biscuit jointed together

Breaks down into 4 parts to get upstairs as its nearly 100kg

Hopefully something he can keep and be around long after me

 

[MetalMonkey]

I needed a couple of 1" bsp nipples urgently to sort out a plumbing issue.

Local plumb centre or whatever they are called now had them in stock. Great.
Couple of quid I naively though, no £7 each… Ow much?! Sod that I’ll make them I declared.

Consequently wasted a couple of hours digging around to find a piece of scrap pipe that wasn’t in too terrible condition, cleaning it up and finding the Presto Minor and working out an ingenious way to hold them.
It almost certainly wasn’t worth it, but it made me feel better.

Anybody else fall foul of the curse of knowing you have the tools and probably the materials somewhere and thus feeling obliged to use them even when it probably wasn’t the smartest idea?
At least it didn’t leak, that would have been embarrassing.

 

[MattF]

What's the point of having the gear, if not to use it when needed.

 

[ukracer]

I needed a couple of 1" bsp nipples urgently to sort out a plumbing issue.

Local plumb centre or whatever they are called now had them in stock. Great.
Couple of quid I naively though, no £7 each… Ow much?! Sod that I’ll make them I declared.

Consequently wasted a couple of hours digging around to find a piece of scrap pipe that wasn’t in too terrible condition, cleaning it up and finding the Presto Minor and working out an ingenious way to hold them.
It almost certainly wasn’t worth it, but it made me feel better.

Anybody else fall foul of the curse of knowing you have the tools and probably the materials somewhere and thus feeling obliged to use them even when it probably wasn’t the smartest idea?
At least it didn’t leak, that would have been embarrassing.


View attachment 469697

Yep. As pointed out my photos of the compressor tanks are not good. But I did not even contemplate using soap and water as I have a jet wash....which was not available at the time. Lol

 

[Hitch]

Helping out a mate for a bit this morning. Making some big sieve things. Not a huge amount of work, but a bit awkward.
Folded channels from 2mm stainless, then rolled to 1200 diameter. That's the first step of the job done.

 

[Brad93]

Helping out a mate for a bit this morning. Making some big sieve things. Not a huge amount of work, but a bit awkward.
Folded channels from 2mm stainless, then rolled to 1200 diameter. That's the first step of the job done.

View attachment 469750 View attachment 469751

Magician

 

[dan.taylor.1]

1st pic looks like a bit of sculpture!!

 

[6ply]

Finished making the motor bracket and securing strut. Next job, make or purchase two pulleys.

 

[DAPPH]

Almost finished this desk for my son he designed and was meant to help....

made from 6 old scaffold boards sawn in half planned down and biscuit jointed together

Breaks down into 4 parts to get upstairs as its nearly 100kg

Hopefully something he can keep and be around long after me

View attachment 469686

Hope you signed & dated it under the top or like a lady friend did with her bespoke dining table , she had everyone who came to her home sign their name & date on the top then after 12 years had a plate glass top cut for it .