Arc Tourist
Member
- Messages
- 4,896
- Location
- Wales
- Thread starter God mode restorations
- Start date
Hood
I am obsessed.
- Messages
- 17,315
- Location
- Carnoustie, Scotland
If I have to use someone else's 4 1/2"grinder because I have forgotten mine then I will leave the guard on but find it a PITA but would rather that than have the owner use it and do damage to themselves. I will however not forget my own the next day and if they use mine and do damage then tuff
EDIT
Just to clarify this is 4 1/2" grinder with a flap disc. I use a guard with a cutting disc, well most of the time as I must admit I have once or twice used it without for small cuts but I do not like doing so and avoid if possible.
Tangledfeet
Think outside, no box required.
- Messages
- 3,114
- Location
- Top of a hill above St Andrews, Fife
Not made... more bodged.
In a moment of buffoonery I managed to knock my FEMI bandaw off the bench and broke its most critical component;
The bargain Sherman TIG206P meant that I could have a go at bodging a fix (alas my beloved Lorch MicorTIG is DC) before I can get hold oc a replacement part. Its about 1deg out vertically as I put way too much filler and heat into it but I'm hoping some filing and washers might fix that. A messy weld and got heaps contamination but its made a few cuts and held!
In a moment of buffoonery I managed to knock my FEMI bandaw off the bench and broke its most critical component;
The bargain Sherman TIG206P meant that I could have a go at bodging a fix (alas my beloved Lorch MicorTIG is DC) before I can get hold oc a replacement part. Its about 1deg out vertically as I put way too much filler and heat into it but I'm hoping some filing and washers might fix that. A messy weld and got heaps contamination but its made a few cuts and held!
Mick Annick
Forum Supporter
- Messages
- 2,634
- Location
- Burgundy, France (450 miles SE of Somerset)
roofman
Purveyor of fine English buckets and mops
- Messages
- 12,191
- Location
- North West with water on 3 sides
looks like it has a TY50/TY80 tank and a tasty flatside too
Dcal
Member
- Messages
- 3,961
- Location
- Antrim Northern Ireland
Today I made my home made 125x 8mm box look more like 125 x 6mm box.
The thicker wall the box has the rounder the corners and as I was trying to match this I ran a few beads on the corners
and sanded most of it off to give me a squarer looking box section.
Then finished making the repair piece for the jack leg and trial fit.
A few tweaks and welded it on
Even gave it a rattle with a bristle blaster and a lick of Jotun
The thicker wall the box has the rounder the corners and as I was trying to match this I ran a few beads on the corners
and sanded most of it off to give me a squarer looking box section.
Then finished making the repair piece for the jack leg and trial fit.
A few tweaks and welded it on
Even gave it a rattle with a bristle blaster and a lick of Jotun
Windy Miller
Semi-Professional Potterer!
- Messages
- 3,595
- Location
- North Kent, UK
Very neat job Dcal - nobody will even notice it’s been fixed.
It’s almost a shame to hide all that good work you put into it!
It’s almost a shame to hide all that good work you put into it!
lchris21
Member
- Messages
- 1,965
- Location
- South Wales
nice work. i like it and the bike!....how did you get the rear shrinking done? might have a bash...........literally on my next project
It’s starting to mature.
Dr.Al
Forum Supporter
- Messages
- 2,236
- Location
- Gloucestershire, UK
Today I made (or at least sort-of-finished-making) a plank of wood out of lots of offcuts of four different hardwoods, all cut into equal width strips and glued together:
It's a bit over 240 mm deep, about 820 mm long and about 9 mm thick. The plan is currently to trim it into a rounded-rectangle sort of shape and use it as a monitor stand for my two monitors, but having seen it, I'm wondering if it might be a bit of a shame to cover a significant proportion of it with the bases of the two monitors, so I might use it for something else.
There are quite a few imperfections (and a couple of aligned joints that I tried really hard to avoid, but must have done something wrong in the glue-up), but as this was my first attempt at something like that, I'm really pleased with how it has come out.
It's a bit over 240 mm deep, about 820 mm long and about 9 mm thick. The plan is currently to trim it into a rounded-rectangle sort of shape and use it as a monitor stand for my two monitors, but having seen it, I'm wondering if it might be a bit of a shame to cover a significant proportion of it with the bases of the two monitors, so I might use it for something else.
There are quite a few imperfections (and a couple of aligned joints that I tried really hard to avoid, but must have done something wrong in the glue-up), but as this was my first attempt at something like that, I'm really pleased with how it has come out.
Dcal
Member
- Messages
- 3,961
- Location
- Antrim Northern Ireland
But just think how you would have felt if you didn't have an AC tig to sort it?
Memmeddu
Member
- Messages
- 4,794
- Location
- Italia Sardegna
Replaced the diaphragms and the primer pump on my friend Husqvarna chainsaw
Can't understand why you love those things....
3 hours spent to figure out the way to extract the carburettor from the chainsaw .
After struggling with it because no fuel was flowing through it , assembled disassemble it at least 10 times ,I've managed to make it working .
But I had to delay the carb tuning to tomorrow
Otherwise I would catch a bullet shot from a neighbor
I've accomplished to get it running 10 minutes ago
Can't understand why you love those things....
3 hours spent to figure out the way to extract the carburettor from the chainsaw .
After struggling with it because no fuel was flowing through it , assembled disassemble it at least 10 times ,I've managed to make it working .
But I had to delay the carb tuning to tomorrow
Otherwise I would catch a bullet shot from a neighbor
I've accomplished to get it running 10 minutes ago
Barking Mat
Cuddler of hedgehogs.
- Messages
- 12,928
- Location
- France, Brittany.
Un peu de soudage à l'arc, heureusement pas les meilleures photos, mais bon.
Help @eLuSiVeMiTe , if I post from my phone it's in french???
But of arc welding today, happily the photos don't do justice, ha, ha, 14 ton rated ring pull, 60 x60 x4 wedged the nose after I cut it down with a grinder to fit in the box, stuck some scrap in to fill the vertical height.
Covered it in multiple runs of 3.2 6013, I liked the penetration, worked for me, my welds are generally over done.
The other rusty shorter one is one I did years ago with my Oxford lump, this was with an italian? Inverter.
Can't really say I notice the difference.
But I'm an occasional welder.
Help @eLuSiVeMiTe , if I post from my phone it's in french???
But of arc welding today, happily the photos don't do justice, ha, ha, 14 ton rated ring pull, 60 x60 x4 wedged the nose after I cut it down with a grinder to fit in the box, stuck some scrap in to fill the vertical height.
Covered it in multiple runs of 3.2 6013, I liked the penetration, worked for me, my welds are generally over done.
The other rusty shorter one is one I did years ago with my Oxford lump, this was with an italian? Inverter.
Can't really say I notice the difference.
But I'm an occasional welder.
arther dailey
Member
- Messages
- 6,437
- Location
- England
good job, any chance of a link to those clamps your using ? cheers
Tangledfeet
Think outside, no box required.
- Messages
- 3,114
- Location
- Top of a hill above St Andrews, Fife
Thanks! Spent this morning doing some filing to get things realigned and it's back to previous accuracy but have enquired about a replacement bracket.
The clamp at the rear is a Milwaukee Torque Lock clamp and the two wee ones (the ones I'm sure you're asking about) are small Kant Twist clamps that I bought several years ago from MSC Direct. They're very handy!
https://www.mscdirect.co.uk/CGI/INSRCH?N=4294966345
The clamp at the rear is a Milwaukee Torque Lock clamp and the two wee ones (the ones I'm sure you're asking about) are small Kant Twist clamps that I bought several years ago from MSC Direct. They're very handy!
https://www.mscdirect.co.uk/CGI/INSRCH?N=4294966345
arther dailey
Member
- Messages
- 6,437
- Location
- England
sheesh that was quick ,thanks , what size are those fellas your using if you can remember (no rush!)
Tangledfeet
Think outside, no box required.
- Messages
- 3,114
- Location
- Top of a hill above St Andrews, Fife
@arther dailey Nae worries! Just popped out to grab one as I wasn't sure; mine are the model 405 / 2" clamp. In an ideal world I'd have a selection, alas two of these will have to suffice!
