Today I acquired...........

[Kram]

Looks like seller chopped the 100mm bar off with a 4" grinder and hacksawed the 50mm in the middle

 

[DAPPH]

@ qwakers
This is the tool post I have for you if you want it . It takes a half inch tool , is approx. 75x75 mm .
I've included the bolt washer & nut .. you'll have to use your own threaded bar or ring spanner to tighten the nut which is Metric .

 

[qwakers]

you're a legend buddy. send me a pm with how much you want for it and ill get the £££ across to you.

 

[DAPPH]

Picked these 36" bolt cutters up for 30 quid. They're in really good nick!View attachment 226646

Any good for picking padlocks ?

 

[DAPPH]

you're a legend buddy. send me a pm with how much you want for it and ill get the £££ across to you.

It's FOC , I'll let you know the P&P & insurance in the morning as I will be using my lasses account as it cheaper .

PM me your address , email & phone number asap .

 

[nickk]

As prompted by a thread on here,I got this,and am impressed,the gouge in the trailer eye is approx 0.1mm deep,in less than 30 seconds.

 

[Cobbler]

That looks the same as the Lidl one, even down to the triangular side on the switch. A very useful tool to have.

 

[Pigeon_Droppings2]

I use the orange black and decker one and it's excellent....takes a real beating...tried evolution and didn't get on with it at all (just used to spit the belts across the room!).

Also don't buy the dedicated belts...it's very easy to buy wide sanding belts, make a small incision with a knife at the required width and then just tear off a new belt....the belts have a grain to them so they tear along the grain which makes it easy.

The pre cut belts seem to cost a lot.....the blue (zircon) belts are excellent....I bulk buy the 75mmx457mm ones and they last me years. Buying individually would cost a fortune!

 

[slim_boy_fat]

I use the orange black and decker one and it's excellent....takes a real beating.

Also don't buy the dedicated belts...it's very easy to buy wide sanding belts, make a small incision with a knife at the required width and then just tear off a new belt....the belts have a grain to them so their tear along the grain which makes it easy.

The pre cut belts seem to cost a lot.....the blue (zircon) belts are excellent.

Aye, that's what I do after seeing the tip on here a while back.

 

[Pigeon_Droppings2]

Aye, that's what I do after seeing the tip on here a while back.

I saw it on here too a long while back (can't remember who came up with it).

That storage box would drive me nuts....having to remove the end of the tool to get it back in the box, why do they always do that....so annoying!

 

[Anguz]

a chinese pulley for my ajax drill modification

 

[Seadog]

Finally!

A tin of black powder

Yes, Kasenit No.1

I've had the search running on eBay for easily two years. This is the first tin with contents that I've seen. Now, what can I do with it?

 

[The_Yellow_Ardvark]

Finally!

A tin of black powder

View attachment 226999

Yes, Kasenit No.1
View attachment 227000

I've had the search running on eBay for easily two years. This is the first tin with contents that I've seen. Now, what can I do with it?

Give it to me.
I am running low on mine.

 

[Seadog]

Shan't

 

[The_Yellow_Ardvark]

Shan't

Why not?

 

[Seadog]

S'mine

 

[The_Yellow_Ardvark]

S'mine

Why?

 

[Seadog]

Cos I bought it. So there

 

[The_Yellow_Ardvark]

Cos I bought it. So there

Oh, why?

 

[Seadog]

Because I could.