- Thread starter monkeymark
- Start date
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
So it is. It's such a poor picture () I thought it was the base I was looking at
At least there is a picture.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
Well, it has taken a few days, but the 2 bill hooks have been "restored". Not to show room condition, but to a working one.
One will go to my friend and one I will keep.
Both were striped down.
The blades were cleaned, warmed to a dull red and dipped into old engine oil, this was repeated 3 times. The tangs were heated to a red colour and allowed to cool slowly to soften it. The cutting edges were cleaned and then heated to a "Purple" temper and dressed with a "Scythe" stone to put a sharp edge on them both.
Both handles and ferrules were in good condition, they just needed a lean up back to bare wood and soaked in a wax based stain. Camp coffee and bee's wax.
Then refitted with a copper Rove rivet on the end of the tang.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
RN Chipping Hammer.
From this. Head was loose, only the remains of a glue repair holding it in place. The ends were completely ruined and the metal was soft.
Striped down. Handle cleaned and was found the head was fitted upside down. So it was refitted and wedged back in place. Even the wedge had a "Broad Arrow" stamped on to it.
Head cleaned, ends reshaped after Hardening and tempering the ends. I did save most of the stampings, so the history has been preserved.
Shaft refitted and waxed with a dark oak wax stain. Now it is sat gathering dust.
From this. Head was loose, only the remains of a glue repair holding it in place. The ends were completely ruined and the metal was soft.
Striped down. Handle cleaned and was found the head was fitted upside down. So it was refitted and wedged back in place. Even the wedge had a "Broad Arrow" stamped on to it.
Head cleaned, ends reshaped after Hardening and tempering the ends. I did save most of the stampings, so the history has been preserved.
Shaft refitted and waxed with a dark oak wax stain. Now it is sat gathering dust.
- Messages
- 22,236
- Location
- Birmingham
Best of luck with it, one of the Land Rover mags decided to buy and run one to dispel the myths about how troublesome they were, after doing articles on replacing the gearbox and complete front hubs there was no mention of it again
zx9
Forum Supporter
- Messages
- 5,171
- Location
- South East London
Best of luck with it, one of the Land Rover mags decided to buy and run one to dispel the myths about how troublesome they were, after doing articles on replacing the gearbox and complete front hubs there was no mention of it again
I did like @winchman 's post but realistically @Robotstar5 is I fear nearer to the mark. I you did not pay a lot for it why not, hope you have a bit of fun and it gets you through at least one winter, you just need to know when to part company. As it happens I am toying with a remarkably cheep E320 from MB's darkest days but I figure if it is so cheep there in not a lot to lose.
winchman
Member
- Messages
- 5,863
- Location
- Merseyside
I bought it from a good friend who looked for ages to find a nice one, lady had had it for 5 years and it wanted for nothing, he bought it on springs with the intention of putting it back on air suspension, need less to say he spent a good few hundred quid trying to get the air to work correctly and then put it back on springs!
It runs well came with 12 months MOT from a garage I trust all for £1000! On classic insurance for £200.
Lets see how it goes at least I shouldn't have to weld it?
zx9
Forum Supporter
- Messages
- 5,171
- Location
- South East London
For a grand it must be worth a punt, enjoy!
Parm
Respect The Sound System
- Messages
- 17,864
- Location
- Towcester
Quite agree, minidsp is the nuts, but it did take me some time to figure it all out.
gaz1
Member
- Messages
- 19,015
- Location
- westyorkshire
saturday i aquired 2 computer base boards memory and cpu for a total of 75.00
am2 mainboard with 60 cpu with 4 gig of memory
am3 mainboard with cpu uknown for the moment with 8 gig of memory
another 3tb hard drive and a 250gb of s3 ssd hard drive
ive also aquired ml7 new/unused cutting tools
am2 mainboard with 60 cpu with 4 gig of memory
am3 mainboard with cpu uknown for the moment with 8 gig of memory
another 3tb hard drive and a 250gb of s3 ssd hard drive
ive also aquired ml7 new/unused cutting tools
Jlg
Member
- Messages
- 2,572
- Location
- Cumbria
They look to good to use
Don't even bother trying the myford tooling, they are rubbish! I have tried them on my ML7 & no matter what I do I get a poor finish. I am now using Chinese carbide tipped tooling & getting perfect finishes every time!
Best thing would be to sell them on ebay for a mad price & you will be able to buy all the carbide tipped tooling you will need from bangood & still have loads of money left over!
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
Set of Das welding goggles.
With a Derpy, fresh from the USA.
gaz1
Member
- Messages
- 19,015
- Location
- westyorkshire
they kinda come from ebay
I kinda wanted 3 tools from them left right and the middle one but i dont mind the rest of them
cheeky comment
would you mind if i try yours if you dont like them or even buy them off you ?
its postage both ways if borrowing them whilst you send the other item as well
eLuSiVeMiTe
Member
- Messages
- 16,441
- Location
- ......
Indexible is a no brainier mate. Won't want to send them back.
I went for a glanze set from Cronus and they've been impeccable.
weldingnovice
Member
- Messages
- 262
- Location
- Northeast
These were in a snap on box I got. They are Weld craft from good ole Uncle Sam land I know they are for tig welding but that's about it.
Any info on this stuff?
Any info on this stuff?
