Arc Tourist
Member
- Messages
- 4,884
- Location
- Wales
There are 380 posts in this thread to search through, so could you specify the number of the post you are referring to please ?
- Thread starter arthur
- Start date
tom-madbiker
Member
- Messages
- 322
- Location
- Chesham, UK
tom-madbiker
Member
- Messages
- 322
- Location
- Chesham, UK
Post 224
Arc Tourist
Member
- Messages
- 4,884
- Location
- Wales
1mm, I wouldn't be confident either. Consider welding some angle iron underneath across to both sides of the axel supports ?
LewisT
Member
- Messages
- 225
- Location
- Central Scotland
Seems to take the weight ok, if it deforms much i will cut out the bottom and add a few strips of flat bar underneath, and for the first time in two years the gas bottle is no long in danger of getting knocked over, probably going to add a shelf on top but that can wait till another day.
Stueeee
Old git
- Messages
- 1,043
- Location
- N W Kent
Just got mine pretty much finished now. The idea was to make something which would take my new Plasma cutter and my new-to-me TIG welder as well as my home made Heath Robinson TIG cooler. The frame was made of some supports off an old desk, some 1.5mm steel sheet and some 25mm square ERW tube. Most of this was kicking around the workshop or fished out of the scrap bin.
Got the wiring laid out here. There's 6 metres of cable with a 32A 5 pin 415v plug. This is distributed into 32A 240V for the plasma cutter. 3 off 15A fused phases for the welder, and a 13A socket for the cooler.
Sprayed this with some 2 pack primer.
Sprayed this again with some synthetic red paint afterwards. Then started loading/hanging the various bits on it...
The drawers were a bit of a faff to install, but I find that there is so much widgetary with TIG welding that I don't think it will be difficult to fill them up...
Although this setup looks really chunky, it's quite a bit smaller (and much more manouverable than my existing BOC ADR 300 AC/DC TIG welder.
Got the wiring laid out here. There's 6 metres of cable with a 32A 5 pin 415v plug. This is distributed into 32A 240V for the plasma cutter. 3 off 15A fused phases for the welder, and a 13A socket for the cooler.
Sprayed this with some 2 pack primer.
Sprayed this again with some synthetic red paint afterwards. Then started loading/hanging the various bits on it...
The drawers were a bit of a faff to install, but I find that there is so much widgetary with TIG welding that I don't think it will be difficult to fill them up...
Although this setup looks really chunky, it's quite a bit smaller (and much more manouverable than my existing BOC ADR 300 AC/DC TIG welder.
Start taking orders for it!
Work in progress, plug welding 1mm sheet to the bottom not entirely confident that the gas bottle wont go through it.
1mm is plenty if your spot welds are strong, if you don't want the sheet to deflect or risk the spot welds breaking off then as some else said, put a bit of angle or SHS under it. I regularly walk over my sheet metal trim deck roof on the shed and that is only 0.5mm thick with a frame span of 1.3m and I am 96kg.Work in progress, plug welding 1mm sheet to the bottom not entirely confident that the gas bottle wont go through it.
Dcal
Member
- Messages
- 3,954
- Location
- Antrim Northern Ireland
I'm loving this thread.
Has anybody included a fire extinguisher on their trolley?
I have some inch box section I think I might make up a trolley for mine and get in on this action
Show us your welding cart/trolley...
mine will probably end up over engineered with taper roller bearings and a brake then hardly ever get used. :ashamed: Now, there's an idea.
www.mig-welding.co.uk
I'm loving this thread.
Has anybody included a fire extinguisher on their trolley?
I have some inch box section I think I might make up a trolley for mine and get in on this action
An extinguisher is in my plans, as well as a water container & a fire blanket.
Sergei Slovenija
Member
- Messages
- 1,267
- Location
- Slovenija Ljubljana
I have limited space for mechanical work, and in the summer I prefer to welding in the yard. Therefore, all equipment must be placed on wheels for mobility.
A small overview of my options for welding carts and metal saw carts
And stuff like that
A small overview of my options for welding carts and metal saw carts
And stuff like that
James1979
Member
- Messages
- 8,434
- Location
- Orkney
You have some good stuff on your channel, and welcome.
Sergei Slovenija
Member
- Messages
- 1,267
- Location
- Slovenija Ljubljana
I thought forums went extinct like dinosaurs, but NO
Google only shows in search what it considers useful.
However, I found)). It's a nice club here.
