Stuff you have fixed today

[The_Yellow_Ardvark]

This engine was stripped down, cleaned and just given a wax.

The flywheel was out of true, so I asked a friend to alow me to use his press. I few gentle press runs had it true.

Oddly, after it was wax, so residue of the solid fuel tablets seamed to hace leached out form hard to reach parts.
A buff uop had them removed.



This is how this engine came my way.
Flywheel was not on the engine.
Safety valve was stuck in a semi open position.

As the engine is original condition, very little was done to it.

It was stripped down, as the pipe from the boiler was weeping.
The flywheel was worn. But as it was a 1959 engine the fly wheel had a hole drilled, but not tapped, in it.
So I taped it out and using a mecanno screw fitted it.

A few Massed Mamods.

 

[awemawson]

Our Klargester private sewage plant had roots coming out of it's clean water discharge pipe. It was installed over 20 years ago prior to our ownership, and we had had an attempt at clearing it 12 years ago when we dredged the stream that it discharges into. Not easy requiring 'volunteer' to sit in digger bucket suspended over the stream from the opposite side. But although the pumped discharge water still flowed it obviously needed clearing.

It had been installed with no provision for rodding the pipe, which was about 10 metres of 50 mm plastic, transitioning into 110 underground brown pipe for an unknown length with no indication where the joint was.

Time to take the bull by the horns and this week I've had a young and fit chap trenching the lot out from the stream to the sewage plant - quite deep - loads of spoil.

Yesterday we got to the 'root' of the problem - the bodging installers had just slipped about 30" of 110 mm brown pipe over the end of the 50 mm plastic WITH NO COUPLER. Add in the fact that the stream bank is awash with willow and alder and of course their roots just took up residence until it was jam pack full. I've never seen a pipe so blocked.

The fix, run 110mm underground sewer pipe all the way from the Klargester pump outlet to the stream and incorporate a rodding eye, and a little inspection chamber for access to the rodding and and the 50 / 110 mm transition so in the future not only can the pipe be rodded but the transition joint can be inspected.

I am amazed that water was still getting through that clogged pipe - though it is a powerful pump.

 

[Edward Teach]

Our Klargester private sewage plant had roots coming out of it's clean water discharge pipe. It was installed over 20 years ago prior to our ownership, and we had had an attempt at clearing it 12 years ago when we dredged the stream that it discharges into. Not easy requiring 'volunteer' to sit in digger bucket suspended over the stream from the opposite side. But although the pumped discharge water still flowed it obviously needed clearing.

It had been installed with no provision for rodding the pipe, which was about 10 metres of 50 mm plastic, transitioning into 110 underground brown pipe for an unknown length with no indication where the joint was.

Time to take the bull by the horns and this week I've had a young and fit chap trenching the lot out from the stream to the sewage plant - quite deep - loads of spoil.

Yesterday we got to the 'root' of the problem - the bodging installers had just slipped about 30" of 110 mm brown pipe over the end of the 50 mm plastic WITH NO COUPLER. Add in the fact that the stream bank is awash with willow and alder and of course their roots just took up residence until it was jam pack full. I've never seen a pipe so blocked.

The fix, run 110mm underground sewer pipe all the way from the Klargester pump outlet to the stream and incorporate a rodding eye, and a little inspection chamber for access to the rodding and and the 50 / 110 mm transition so in the future not only can the pipe be rodded but the transition joint can be inspected.

I am amazed that water was still getting through that clogged pipe - though it is a powerful pump.

View attachment 352739
View attachment 352733
View attachment 352734


View attachment 352738

View attachment 352737

View attachment 352736

View attachment 352735

View attachment 352732

Good to see a job done properly

 

[The_Yellow_Ardvark]

This is what 3am is for.

This 1957(approx) SE1 Mamod cam my way. I knew it needed some TLC.
The paint was applied in layes, like butter icing on a cake.

But it did steam. Ok we had a few seals that needed to be replaced. But for its age I was not shocked at that.

The paint stripper worked. But only one layer at a time. Wrapping it in cling film help speed the stipping up. 8 layes of green paint, over the original red.

A fair bit of matel bashing when into getting the plate flat. This plate had no cracks on the mountain holes. That was nice to find. They can be TIG anddressed back. But the plate always warps
There are still some pits and flaws. They are original, so were left.

What so special about this picture?
Nothing, apart from the original felt oil pad. You can tell it is original, as it does not fill the hole it is in.

Fullly assembles. ran on compressed air and when the paint is fully cured I will cook it and run it on steam.

The keen eyes will spotted the con rod looks differant.
It is.
It is a Mamod replacement one. The rotingals were flat plate back when this was made. The connecting hole to crank would become oval very soon. This con rod was supplied as a replacenent.

 

[The_Yellow_Ardvark]

A 1920's Hose nozzle, fitted with a post WW2 hose adapter.
Should not need much.

But it passed no water.

A lump of plastic.

Now fitted with a modern hose adapter.;

 

[The_Yellow_Ardvark]

A simple job.

A Bren Gun Grease container.

B it of a clean.

Then it jopins the Vickers 303 Gun one.

 

[cheb]

I made an adapter for my new to me 18V drill.

 

[Brad93]

I've cleaned some mucky grease, replaced all seals and bearings. Refill with white food safe grease.

 

[James1979]

Made or fixed, not sure

Replaced the poxy wing nut things on Mrs79’s mower as they snapped.

2 minutes to draw them out and about the same to cut them. I put helicoils in rather than directly thread the aluminium.

 

[slim_boy_fat]

^^ Nice to see you're looking after her best interests - don't want anything to interrupt that mowing.

 

[James1979]

^^ Nice to see you're looking after her best interests - don't want anything to interrupt that mowing. Don’t want me to end up using the poxy thing!!!

Fixed it

Deal in exchange for not having 100% concrete is im not cutting the stuff. Happy to “get a man in” but she likes doing it apparently.

I’ve no problem paying someone. Keeps the money local and keeps the money going round.

 

[JMS1972]

This is what 3am is for.

View attachment 352769

This 1957(approx) SE1 Mamod cam my way. I knew it needed some TLC.
The paint was applied in layes, like butter icing on a cake.



View attachment 352770

But it did steam. Ok we had a few seals that needed to be replaced. But for its age I was not shocked at that.

View attachment 352771

The paint stripper worked. But only one layer at a time. Wrapping it in cling film help speed the stipping up. 8 layes of green paint, over the original red.

View attachment 352772

A fair bit of matel bashing when into getting the plate flat. This plate had no cracks on the mountain holes. That was nice to find. They can be TIG anddressed back. But the plate always warps
There are still some pits and flaws. They are original, so were left.

View attachment 352773

What so special about this picture?
Nothing, apart from the original felt oil pad. You can tell it is original, as it does not fill the hole it is in.


View attachment 352774



Fullly assembles. ran on compressed air and when the paint is fully cured I will cook it and run it on steam.

View attachment 352775


The keen eyes will spotted the con rod looks differant.
It is.
It is a Mamod replacement one. The rotingals were flat plate back when this was made. The connecting hole to crank would become oval very soon. This con rod was supplied as a replacenent.

If you send me a back of a fag packet drawing I can easily make you some spare felt pads on the CO2 laser.

 

[Tinbasherdan]

Its scarey when you look under some motors and see what the towbar is attached to, mainly rust on a lot of them!

I put a rear 1/4 on a discovery two for a friend. “It’s not terrible, I just want peace of mind” his ricker fell out when I dropped the tank and showed him the only thing keeping his nice big horse box attached was the sum total of about 6” of metal across both legs

 

[Blobber]

I put a rear 1/4 on a discovery two for a friend. “It’s not terrible, I just want peace of mind” his ricker fell out when I dropped the tank and showed him the only thing keeping his nice big horse box attached was the sum total of about 6” of metal across both legs

I spent a week under a Discovery 1 chasing the rust for a mate, never again!!

 

[Tinbasherdan]

I spent a week under a Discovery 1 chasing the rust for a mate, never again!!

my d1 was the most solid ive ever seen, mainly on account of 3 months of welding!

 

[minimutly]

I spent a week under a Discovery 1 chasing the rust for a mate, never again!!

Doing welding jobs for a mate - the worst jobs ever. Mine was a metro for a mate who had Lymphoma. Days of welding...

 

[Blobber]

Doing welding jobs for a mate - the worst jobs ever. Mine was a metro for a mate who had Lymphoma. Days of welding...

I wouldnt mind but hes not a mate now!!!

 

[DennisCA]

Filled my own AC in the car, it's cold now, not just a cool breeze. Great when it's 30C outside, that's no weather for a finn, but I handle it better than most.

 

[Tigman]

Just fixed this cast iron machine part , old mill apparently, 2 breaks , vee on the inside first , fit together and a bit of pre-heat weld up with LINC Cast31 NiFe 2.5 Rod about 85 amps , little bit of peening , then vee out the outside breaks and weld again , peening marks can be seen all over the welds , cooling down slowly now , hope it doesn't crack again !

 

[Blobber]

The little Leyland has to work its socks off with the baler so I like to do a little service before hand, already done an oil change so fuel filter next
Pump bowl, Yuk!

Better

Fuel Filter, yuk as well!

In my stash of Vauxhall/Opel spares I have plenty of quality filters!

Jobs a goodun, bled through and ready to work!