Stuff you have made today

[Erie Fred]

This one has 4 down speeds and reverse
I was going to replace it as part of the spruce up with something shiny but it just makes me smile


View attachment 377981

I've run some industrial drill press's that shoving the quill feed handle sideways engages power feed.

 

[Gragson]

I've run some industrial drill press's that shoving the quill feed handle sideways engages power feed.

Ah but, my imaginary power feed goes to 11!

 

[julianthegypsy]

I've run some industrial drill press's that shoving the quill feed handle sideways engages power feed.

That would be a Pollard Corona. Beautiful.

 

[Sergei Slovenija]

Completed the piping. Cuts, inserts, turns and so on. Complete alteration of heating, cooling and vacuum lines, under the new layout of equipment.

 

[Norsk]

A mate wanted a big oak table, i made him one. Its 286cmx110.

I have to take it apart to fit it in my car.I could have put it on the roif but we would need a tractor to unload it.

 

[Fraserb]

A mate wanted a big oak table, i made him one. Its 286cmx110.

I have to take it apart to fit it in my car.I could have put it on the roif but we would need a tractor to unload it.

View attachment 378156 View attachment 378157

Reminds me of when I made a big steel burner for someone, after it was made he was passing with a trailer so we just dropped it on with one of our forklifts, wasn't until he got home he realised he doesn't have a forklift at the other end and it was a lot heavier than expected, fortunately a few mates managed to lift it off.

 

[Onoff]

Bubble, leftover turkey some pickles and hummus.

 

[Norsk]

Bubble, leftover turkey some pickles and hummus.

View attachment 378170

I
Seeing those pickled onions made my mouth water.
I have to make some.

 

[striker]

I made loads of swarf, 40 X 20mm holes and cut some channel and plate.
A little more to do, then some arc welding!

 

[6ply]

More t-nuts. Milled a length so I'll have plenty.

 

[6ply]

Mostly use 3/8" threaded rod, but needed some smaller m6 threaded t-nuts.

 

[6ply]

Another shot in case anyone asks if they are fully threaded. Yes. But centre punched to prevent screwing through.

 

[eLuSiVeMiTe]

Bubble, leftover turkey some pickles and hummus.

View attachment 378170

Talking of bubble. I made my own hash browns Christmas eve. Went down very well.

Boiled in the skin for ten minutes then grated them up with butter. Nom

 

[ukracer]

Another 2000 squares finished today...
Now my tool has broken.

 

[Maker]

I made a gift tag (Bit late I know).



I can't remember what that layered card technique is called, but it took bloody ages with two pairs of sharp tweezers.

 

[Kram]

Another 2000 squares finished today...
Now my tool has broken.

Squares of what? can you mig it?

 

[W.olly]

Made a pulley for the overhead storage today. Do the trick I hop lol

 

[ukracer]

Squares of what? can you mig it?

Lol Squares of felt. Cut from 15 metre rolls.
Squares end up 275mm with a 50mm center punched hole.

The tool is plastic and has split. It was a jovial post. In the spirit of the season.

I have just 3D printed a new one.


There is the split on the old one

 

[Dev]

thats The sort of 3D print that might benefit from annealing. Not joking, it’s a thing for adding strength.

 

[pcwizme]

Lol Squares of felt. Cut from 15 metre rolls.
Squares end up 275mm with a 50mm center punched hole.

The tool is plastic and has split. It was a jovial post. In the spirit of the season.

I have just 3D printed a new one.
View attachment 378234

There is the split on the old oneView attachment 378235

Cutting felt is one of the jobs I leave to the laser now! its so much easier and exact....