slim_boy_fat
Forum Supporter
- Messages
- 29,540
- Location
- Scottish Highlands
- Thread starter God mode restorations
- Start date
Brad93
Member
- Messages
- 18,415
- Location
- Essex, United Kingdom
I'm not familiar with it? only brasso?
MattF
Forum Supporter
- Messages
- 16,656
- Location
- South Yorkshire
Just a solution you dip it into. You can get it for silver, too.
Mick Annick
Forum Supporter
- Messages
- 2,636
- Location
- Burgundy, France (450 miles SE of Somerset)
Lovely work Brad
I remember that gate posts should be installed "on the batter" (leaning back), so they become vertical when the gate is hung.
Anybody actually do this?
Blobber
Member
- Messages
- 2,556
- Location
- lincolnshire
Not on purpose!
25.4_mechanic
Member
- Messages
- 1,046
- Location
- Germany, southwest
... wouldn't that then only be true in one position, either open or closed?
In the other position, everything would only be worse and would get even worse over time ...
Up to a point, Lord Cropper... wouldn't that then only be true in one position, either open or closed?
In the other position, everything would only be worse and would get even worse over time ...
Gates closed: upright post.
Gates open: if I remember my maths O'Level, half the weight will be in the open position, half in the closed, so post not quite upright, and some lean towards the open position. I expect I'm wrong
25.4_mechanic
Member
- Messages
- 1,046
- Location
- Germany, southwest
DAPPH
as dyslexik as I'm daft
- Messages
- 7,053
- Location
- Near to Cross Hands Llanelli SouthWales GB
Simply put in a big enough concrete foundation three time the weight of the gate & post it hangs off , putting the post in half of the length below the ground has stood the test of time for many many yearsUp to a point, Lord Cropper
Gates closed: upright post.
Gates open: if I remember my maths O'Level, half the weight will be in the open position, half in the closed, so post not quite upright, and some lean towards the open position. I expect I'm wrong
I put my hot dipped galvanised gates on 10 mm thick 100 mm box section galv posts on a carefully levelled up engineering brick set in almost a foot of poured quick set footing concrete at the bottom of the hole , l laser levelled it to the same height on the other side.
A couple of hours later after lunch the quick set had gone off . On each of the hinge pins I set three 35 mm x 5 mm thick brass washers, slipped the posts down into the holes . put the gates on their posts & lashed the gated closed with a 10 mm packing strip between , then lashed a cross bar timber on the top of the gates and got my lass to hold them vertical as I poured in more quickset . Used ratchet straps and floor anchors to hold them vertical under a slight tension till it set using a few bricks and pairs of opposing wedges to take any drop down load off things
That was 24 years ago , 20 years ago they were still perfectly aligned after being opened & closed several times a day .
cheb
Member
- Messages
- 3,392
- Location
- Outer Hebrides
It's a reference to a character in Evelyn Waugh's novel Scoop. Lord Copper owns The Daily Beast and his Foreign Editor, Salter, will never contradict him, and will answer 'Up to a point'. An excellent book, my favourite of Waugh's. 'Feather-footed through the plashy fen passes the questing vole' is another phrase from the book.
Scoop (novel) - Wikipedia
Scoop (1987 film) - Wikipedia
Barking Mat
Cuddler of hedgehogs.
- Messages
- 12,928
- Location
- France, Brittany.
I'm sure it's a Mig Welding Forum rule.It's a reference to a character in Evelyn Waugh's novel Scoop. Lord Copper owns The Daily Beast and his Foreign Editor, Salter, will never contradict him, and will answer 'Up to a point'. An excellent book, my favourite of Waugh's. 'Feather-footed through the plashy fen passes the questing vole' is another phrase from the book.
Scoop (novel) - Wikipedia
en.wikipedia.org
Scoop (1987 film) - Wikipedia
Subsection 3, part 2, paragraph 17 rules of behaviour.
Forum users will not use 'literary allusions' on weekends, especially Evelyn Waugh.
Dr.Al
Forum Supporter
- Messages
- 2,243
- Location
- Gloucestershire, UK
A big pile of semi-dimensioned sweet chestnut. All 20 mm thick and flat and square on three sides (the fourth edge will get dealt with when I've decided on the widths I want and the ends will be done much later). All prepared using a ryoba (Japanese hand saw) and a #5 plane.
I also made a large bin crammed full of plane shavings
I also made a large bin crammed full of plane shavings
cheb
Member
- Messages
- 3,392
- Location
- Outer Hebrides
Agreed, up to a point.
roofman
Purveyor of fine English buckets and mops
- Messages
- 12,195
- Location
- North West with water on 3 sides
How many years experience does it take to turn out work like that?...Stunning job
