Sergei Slovenija
Member
- Messages
- 1,267
- Location
- Slovenija Ljubljana
- Thread starter God mode restorations
- Start date
Blue Chips
Forum Supporter
- Messages
- 622
- Location
- Maine, USA
That has lots of possibilities. It would be interesting to try it on different types of stones and surfaces. Are those etchings all single-pass, or did you do multiple passes?
Hood
I am obsessed.
- Messages
- 17,308
- Location
- Carnoustie, Scotland
All single, just varied feed and power and fill or line.
Sergei Slovenija
Member
- Messages
- 1,267
- Location
- Slovenija Ljubljana
God mode restorations
Member
- Messages
- 8,146
- Location
- uk colchester
Today. Made something completely boring...a set of light brackets for dads little trailer
Hopefuldave
Intergalactic pot-mender
- Messages
- 2,545
- Location
- The Shed of Danger, surrey, England
If you were closer, or if you're passing Camberley / can organise Underground Railway delivery, I have a hatful of computer server rack sliders (heavy-duty ball bearing slides), could be Just Right for your sliding drawer / table - welcome to a couple, if so? I used a pair each for big drawers (full of Metrology) under one of my workbenches so they're up to the job, not THAT difficult to cut down and reassemble if you need to shorten them.Had some left over parts after i repaired the door on the teardrop. I have storage under the bed and find the rear compartment a pain to get too. So a hatch would be ideal and hopefully a slide out 'drawer' that can be used as a table can be added. Progress so far, basic hand tolls and bought nothing for it yet
View attachment 411138View attachment 411139View attachment 411140View attachment 411141View attachment 411142View attachment 411143View attachment 411144View attachment 411145View attachment 411146View attachment 411147
sako243
Member
- Messages
- 3,457
- Location
- My mansion in Wales
Some storage and a counter top in the dark room.
Not perfect but the cupboards were ****ty when they were installed in the old office at my parents place and they haven't improved. One can't complain at them though as they were free in light of it being converted into a granny annex.
Room isn't quite square either so made cutting the tops interesting. They're not perfect but they'll do with a bit of trim / sealant in the gaps.
Not perfect but the cupboards were ****ty when they were installed in the old office at my parents place and they haven't improved. One can't complain at them though as they were free in light of it being converted into a granny annex.
Room isn't quite square either so made cutting the tops interesting. They're not perfect but they'll do with a bit of trim / sealant in the gaps.
AdventuresInMetal
Member
- Messages
- 218
- Location
- North West, England
I've rotated one of my 7" grinders 90 degrees but the other way, its so much nicer to use for a cutting disc.
- Messages
- 13,409
- Location
- England
Think it was Metabo that did them with rotaing handles years ago.
MattF
Forum Supporter
- Messages
- 16,596
- Location
- South Yorkshire
MattF
Forum Supporter
- Messages
- 16,596
- Location
- South Yorkshire
Auto correct by the looks.
Thought you may be getting your own back on the ones who type draw instead of drawer. AdventuresInMetal
Member
- Messages
- 218
- Location
- North West, England
henry Kadzielski
Member
- Messages
- 1,208
- Location
- Australia Wollongong
You can also put welders in that category. Come to thing about it there are many more things that can be includedNo such thing as too many.
Sergei Slovenija
Member
- Messages
- 1,267
- Location
- Slovenija Ljubljana
JOEPRO
Member
- Messages
- 3,246
- Location
- UK
That's going to brew some great coffee right there
