Laser is reflected back off the substitute honeycomb base and damages the light source and/or mirrors. I'm not saying this is certain though.
I have COVID at present but expect to be back at work on Monday - I could ask then.
- Thread starter God mode restorations
- Start date
I have COVID at present but expect to be back at work on Monday - I could ask then.
Hood
I am obsessed.
- Messages
- 17,308
- Location
- Carnoustie, Scotland
Ah ok, don't think it is an issue as it does stainless and is meant to. It is however a diode laser rather than CO2, so that may make a difference.
Fraserb
Member
- Messages
- 1,562
- Location
- Scottish Borders
That's looking fantasticbut I've got to ask if the doors open out over how wide is that step in front of them ? it's hard to tell from the picture . I presume they'll open fully back .
The doors do open fully round against the house, but the plan is to make steps up from the lower level as well, there's also a water feature involved as well.
DAPPH
as dyslexik as I'm daft
- Messages
- 7,011
- Location
- Near to Cross Hands Llanelli SouthWales GB
My nephew has built a similar shed , putting a metre high wall round the open part and then having clear soft plastic drop down /pull ups walls over the still open bits . T'was a godsend at our recent family reunion as it peed down for two hours in the early evening whilst we sampled the bar stocks
henry Kadzielski
Member
- Messages
- 1,208
- Location
- Australia Wollongong
Basically finished the engine install today. Sea trials tomorrow, we'll see how it al goes. So pics of the almost completed project.
Exhaust in, coolers in, hoses made but not fitted yet.
Opera houses for the steering and deck wash pumps in and connected. Again all hoses made but not connected, as space is a premium.
A closer up view of the steering and deck wash pump mounts, with the slider / adjustment supports.
Again a S/S bracket for the Hynautic engine control throttle slave operating the engine electronic throttle actuator.
Back side view of the exhaust, lagged. As soon as I completed constructing the exhaust the owner took it to get the thermal blankets made. Anyway sea trials tomorrow will see if I will be going home tomorrow, here's hoping
Exhaust in, coolers in, hoses made but not fitted yet.
Opera houses for the steering and deck wash pumps in and connected. Again all hoses made but not connected, as space is a premium.
A closer up view of the steering and deck wash pump mounts, with the slider / adjustment supports.
Again a S/S bracket for the Hynautic engine control throttle slave operating the engine electronic throttle actuator.
Back side view of the exhaust, lagged. As soon as I completed constructing the exhaust the owner took it to get the thermal blankets made. Anyway sea trials tomorrow will see if I will be going home tomorrow, here's hoping
“ET phone home”
MattF
Forum Supporter
- Messages
- 16,589
- Location
- South Yorkshire
Misread that first time around8. Thought you'd said: "of my sister". When I saw the photo, was thinking you were being bitchy.
henry Kadzielski
Member
- Messages
- 1,208
- Location
- Australia Wollongong
And it lives
a little job today, just modifying an exhaust U clamp to so that I can stop the exhaust on my hanging too low.
and with a bit of reinforced rubber strap, it is held over the end of stud that is used to hold a metal strap that holds the petrol tank in place.
and with a bit of reinforced rubber strap, it is held over the end of stud that is used to hold a metal strap that holds the petrol tank in place.
Barking Mat
Cuddler of hedgehogs.
- Messages
- 12,917
- Location
- France, Brittany.
Maybe a washer and a nut, on that, might help ?
Hopefuldave
Intergalactic pot-mender
- Messages
- 2,545
- Location
- The Shed of Danger, surrey, England
Did you have to dunk in brick acid to get galvanising off before welding it? Wondering as I'm going to need to do something to hold up a BIY (Bodge It Yerself) centre section for the Crusty Honda, and that looks a good solution...
no both the studding and the exhaust clamp were both zinc plated, an no preparation was done, as its on a stainless exhaust it will have a limited life anyway.
yeah it might
