Stuff you have made today

[Tangledfeet]

@Tangledfeet Well, you're sure to be the only Mandalorian there.

At least I stand a chance of more kids than colleagues recognising it!

 

[Tupers]

I made the final push and finished off the flat track seat and side panels for the XT500 this week. It’s back to the owner to sort out a second set of forks and wheels now.

 

[slim_boy_fat]

It’s back to the owner to sort out a second set of forks and wheels now

And seat padding?

 

[lchris21]

I made the final push and finished off the flat track seat and side panels for the XT500 this week. It’s back to the owner to sort out a second set of forks and wheels now.
View attachment 259395 View attachment 259396 View attachment 259397 View attachment 259398

lovely bit of work on the seat

any in process pics kicking about?

just looked back and found em....

be interested in the process? perhaps you can stick a thread up on the projects page

 

[northwest]

not that we teachers get to see much of each other as we're not allowed to mix, mingle or socialise - not even be in the same room as each other

But you can be in a room full of kids?

 

[roofman]

I made the final push and finished off the flat track seat and side panels for the XT500 this week. It’s back to the owner to sort out a second set of forks and wheels now.
View attachment 259395 View attachment 259396 View attachment 259397 View attachment 259398

going to want a rubber on that kick lever...looks very nice and sits well

 

[Tangledfeet]

But you can be in a room full of kids?

Yup. Same in England; schools stay open under all conditions/tiers; we're now 'essential workers'.

Face coverings at all times for us, yet only mandatory for those in 4th (KS4) year and up. Strange how the only classes that have contracted it and been sent home are S2...

 

[selectedgrub]

I made the final push and finished off the flat track seat and side panels for the XT500 this week. It’s back to the owner to sort out a second set of forks and wheels now.

Stallion job, well done.

 

[Dieselman 63]

Just a simple rail for all my Britool ring open ended spanners. Three sets I’m trying to make up, Metric (quite a lot), A/F (some) and British (hardly any!).

 

[akdaka]

Have you allowed enough length on the pegs for duplicates of the same size? I think I have 4or 5 of the most common sizes. I keep them all locked in my toolbox when I am not there even though nobody ventures in to my workshop except me.

Just a simple rail for all my Britool ring open ended spanners. Three sets I’m trying to make up, Metric (quite a lot), A/F (some) and British (hardly any!).

 

[3000alloy]

New 2x72 belt sander drive wheel to give more rpm's. It ain't pretty or perfect but it'll do.

 

[optima21]

not made but lightened a small motor as one of the model boats Im building needs to go on a diet..... the motor can started off at 13 grams in weight and is now 2 grams lighter. also shown with a standard motor and a pound coin for scale

 

[Dr.Al]

Mostly yesterday, partly today. Cut up my next-door neighbours old TV aerial pole, cleaned the bits up a little with a polishing thingy on an angle grinder and made some little brackets to help them stand upright. Brackets are a fairly close sliding fit on the poles and are held in place with the green magic that is Loctite 603.

I then spent a lot of time getting all the Christmas-decoration-like aluminium swarf out of the lathe bed.

 

[Hood]

Got a bit done to the tool holder, still have to weld some bits in the back to stop the holders coggling Probably should have just had plain slats and welded on some flat bar to locate into the dovetails but where is the fun in that

 

[Brad93]

Started on a 5” catch plate. Making it up as I go along really.

this blues face is flat with a good finish so I’m going to bore the 4” register tomorrow, drill and counter bore for 6 studs on the rotary table.

after that I will mount to the 5” backplate, remove 3 jaw and do the rest of the Turning, facing and finish boring with the backplate installed on the lathe. Everything will then be dead true to the spindle.

Bore will match the backplate, 2-⅛”, OD will be 5-½” and thickness will be whatever it ends up at.

 

[Tangledfeet]

Aside from even more mess in the workshop after work this evening, I made more progress on Mando helmet - and an instant MIG torch stand. The component parts of the former are now fully welded and cleaned up, just needs more shaping with my Thor copper/hide mallet before wrangling together and transmogrifying so I can actually wear it without toppling forward due to the weight of the monster I have created...

 

[Dieselman 63]

Have you allowed enough length on the pegs for duplicates of the same size? I think I have 4or 5 of the most common sizes. I keep them all locked in my toolbox when I am not there even though nobody ventures in to my workshop except me.

Duplicates just get resold.

 

[Brad93]

Aside from even more mess in the workshop after work this evening, I made more progress on Mando helmet - and an instant MIG torch stand. The component parts of the former are now fully welded and cleaned up, just needs more shaping with my Thor copper/hide mallet before wrangling together and transmogrifying so I can actually wear it without toppling forward due to the weight of the monster I have created...

View attachment 259484 View attachment 259485

Needed titanium

 

[Tangledfeet]

Needed titanium

Ideally it'd be Beskar, the material from which it is made in Sci-Fi world; resistant to blaster shots and (supposedly) the light sabre - guess that last property would make it impossible to TIG weld!

 

[brightspark]

made a quick rough and ready jig and knocked ten of these up for a mates boat trailer there only mild steel so easy to bend