Stuff you have made today

[cianh91]

I want an honest answer now! Are those gate posts going to have a pillar built around them OR did you make the gates too narrow?
On second thoughts, it must be the former as you're a happy chappy judging from the 3rd piccy Nice work though.

No there the right size thankfully . Had to be done that way for the piers and to avoid a water main on one side

 

[DennisCA]

Made this jig so I could plane down this end grain cutting board I am making.

Worked pretty well despite the small router bit I was using (19mm or 3/4"), need to get a proper bit for planing. And I'd have less work sanding that pattern out.

 

[Nick DV]

No there the right size thankfully . Had to be done that way for the piers and to avoid a water main on one side

They look good, and TBH I would have never thought of using I beams as gate posts in this way.

 

[Hood]

Today I made my cooler work again.

aye, £89 for an 8m one. New motor will likely be more

Looks like I was lucky, or certainly seems that way. I removed the pump and motor started no probs, put the pump back on and sometimes it started, sometimes it didn't. Onto RS and ordered a new cap and it seems to have cured it, well so far anyway.
So £4.14 for the cap and I am only £89 down for a torch

Culprit.

 

[123hotchef]

Finally got round to making a board today, to protect the ways when changing chucks.

View attachment 280313

I had one used it for something else cant mind what now though need to make another.

 

[MattF]

I had one used it for something else cant mind what now though need to make another.

It's something which has been on my to-do list for ages. Made it long so that I have to wind the carriage almost to the end of the bed too. Should hopefully stop me stabbing myself on the back of the hand with whichever tool is fitted at the time.

 

[Blue Chips]

I borrowed a few ideas from holders I’ve seen online. My variation on the ones I’ve seen was to make two sets of cutouts, one for a larger TIG torch and one for a smaller TIG torch, which could be rotated to select the size. I don’t think that’s a new idea, as there are almost certainly people who are smarter, faster, and better looking than I am who thought of it first, but here it is.

Two opposed pairs of Belleville disc springs provide adjustable clamping force to maintain the selected position with enough resistance to keep it from rotating when in use, but still allow it to be rotated by hand. The multiple Belleville disc springs provide a wider, less-sensitive adjustment range than a single Belleville spring. The switchable magnet makes it easy to reposition, and it can drop any beard of ferrous debris that it might grow. The magnet can also serve double-duty as a setup magnet. As with other magnetic bases, it’s much more strongly attracted to a thick steel bench top than a thin one. If the steel top is too thin, the magnet might not hold adequately.

My usual disclaimer: I do not guarantee the safety, efficacy, or applicability of the devices, designs, or ideas I have described here. Any use of these devices, designs, or ideas is entirely at your own risk.

 

[123hotchef]

I borrowed a few ideas from holders I’ve seen online. My variation on the ones I’ve seen was to make two sets of cutouts, one for a larger TIG torch and one for a smaller TIG torch, which could be rotated to select the size. I don’t think that’s a new idea, as there are almost certainly people who are smarter, faster, and better looking than I am who thought of it first, but here it is.

View attachment 280710

View attachment 280711

View attachment 280712

Two opposed pairs of Belleville disc springs provide adjustable clamping force to maintain the selected position with enough resistance to keep it from rotating when in use, but still allow it to be rotated by hand. The multiple Belleville disc springs provide a wider, less-sensitive adjustment range than a single Belleville spring. The switchable magnet makes it easy to reposition, and it can drop any beard of ferrous debris that it might grow. The magnet can also serve double-duty as a setup magnet. As with other magnetic bases, it’s much more strongly attracted to a thick steel bench top than a thin one. If the steel top is too thin, the magnet might not hold adequately.

View attachment 280709

My usual disclaimer: I do not guarantee the safety, efficacy, or applicability of the devices, designs, or ideas I have described here. Any use of these devices, designs, or ideas is entirely at your own risk.

nice job I lkie that

 

[Munkul]

I borrowed a few ideas from holders I’ve seen online. My variation on the ones I’ve seen was to make two sets of cutouts, one for a larger TIG torch and one for a smaller TIG torch, which could be rotated to select the size. I don’t think that’s a new idea, as there are almost certainly people who are smarter, faster, and better looking than I am who thought of it first, but here it is.

I like the magswitch base. I bought a couple of cheap TIG torch holders similar to what you've seen for sale, they work fine but I hate the permanent magnets.

 

[Blue Chips]

nice job I lkie that

I like the magswitch base. I bought a couple of cheap TIG torch holders similar to what you've seen for sale, they work fine but I hate the permanent magnets.

Thanks. As budget allows, I'm trying to gradually replace my permanent magnet setup stuff with switchable magnets. Definitely less hassle and less messy.

 

[slim_boy_fat]

Today, I finished 'wood-bothering' in the shape of a stand to hold my spare Winter alloys over the Summer - mainly to keep them at ground level and up as getting them into the allocated corner [partly below garden level] was a real chore and sore on my old back.... Heavy buggers, these wheel/tyre combos.....

Just got a couple of coats of preservative on before the rain started - pics when it stops, which may be some days if you believe forecasts.

 

[Fraserb]

Stainless badge for a front box.

 

[DennisCA]

Oiled the cutting board:

 

[Dr.Al]

Oiled the cutting board:

Looks lovely. What wood is that?

 

[Nick DV]

Oiled the cutting board:

Nice work

 

[DennisCA]

Thanks, it's european oak

 

[Brad93]

Fixed. Some parts for a friend of a forum member

yes that is a gauge block. No it’s not a good one, it was rolling around in a box when I found it.

 

[Memmeddu]

Went to visit the local machinist this morning .
At least they have an idea of who I am and not just a curriculum.
Presented myself , explained my reasons why I'd like to learn this job.
Explained that I currently have no experience in machining but I'd like to learn .
They asked what I'm able to do related to their job ,read and use calipers, micrometers (0.01 resolution) and dial indicators.
Stick weld little bit .
They asked if I'm able to assemble and disassemble things , I've explained that I've always had the passion to understand how things work , and that I repair power tools and small engines to make little bit of money.
They asked if I'm able to work on scooters (apparently they work on those engines too so they might be interested in someone able to complete disassemble and put things back together) , and answered that I've had some experience on my friend's ones .
They explained that because of the virus they are considering various options but they will call me if something moves.

5 minutes of my life well worth spent.
Hopefully I gave a good impression.
However it will go it's a success I believe .

 

[Munkul]

Went to visit the local machinist this morning .
At least they have an idea of who I am and not just a curriculum.
Presented myself , explained my reasons why I'd like to learn this job.
Explained that I currently have no experience in machining but I'd like to learn .
They asked what I'm able to do related to their job ,read and use calipers, micrometers (0.01 resolution) and dial indicators.
Stick weld little bit .
They asked if I'm able to assemble and disassemble things , I've explained that I've always had the passion to understand how things work , and that I repair power tools and small engines to make little bit of money.
They asked if I'm able to work on scooters (apparently they work on those engines too so they might be interested in someone able to complete disassemble and put things back together) , and answered that I've had some experience on my friend's ones .
They explained that because of the virus they are considering various options but they will call me if something moves.

5 minutes of my life well worth spent.
Hopefully I gave a good impression.
However it will go it's a success I believe .

Fingers crossed mate. Sounds like you've shown more spirit than 90% of people.

 

[slim_boy_fat]

Just got a couple of coats of preservative on before the rain started - pics when it stops, which may be some days if you believe forecasts.

Don't put too much reliance on forecasts, it's not as bad atm, so.......




Those bits of guttering don't do anything, they're just tucked out of the way. And, yes...the shed will be getting preservative splashed on when time & weather permit. And those bits of paving slab will be gone too, they're purpose was to weight down a tarpaulin which'll be replaced by a 'custom made' cover for the wheel stack.