zx9
Forum Supporter
- Messages
- 5,171
- Location
- South East London
I could make use of some of that channel, if you weren't so far away I'd be asking you about off cuts.
- Thread starter monkeymark
- Start date
- Messages
- 14,513
- Location
- UK
A set of very accurate G clamps. The big ones will be handy for clamping plates on the pillar drill so i'm looking forward to getting started on that job.
Just a couple tools for the lathe.
Right handed quad turn (aka insert drill) to replace the left handed one I'm currently using to avoid needing to reverse the spindle when drilling/boring the hole it gets used for.
And a SCLCL holder to replace a SDFCL holder, so I can use my stock of CCMT inserts, instead of DCMT inserts.
Right handed quad turn (aka insert drill) to replace the left handed one I'm currently using to avoid needing to reverse the spindle when drilling/boring the hole it gets used for.
And a SCLCL holder to replace a SDFCL holder, so I can use my stock of CCMT inserts, instead of DCMT inserts.
vw-al
Member
- Messages
- 195
- Location
- Rugby
They are for a small Powerfab 125 towable, don’t laugh it does everything I need, it’s cheaper than hiring and easier than a spade.
Pete.
Member
- Messages
- 14,381
- Location
- Kent, UK
I've go two of those they are fantastic.
Kram
Member
- Messages
- 6,857
- Location
- Sussex
Vice bending jaws. Either they sent me a bigger one or my vice has shrunk. Quick test made a soldering iron holder bracket, so that I no longer have it wedged in a slightly open bottom draw as I have for the last 5 years.
Few meters of h05rn-f cable to replace the kinked, short, annoying h03vv on the soldering iron. I couldnt find anything more flexible rated for 240v but Im interested if theres a better option.
bigegg
Scream Not Working Because Space Make Deaf
- Messages
- 9,558
- Location
- Leeds, West Yorkshire
Vice bending jaws. Either they sent me a bigger one or my vice has shrunk. Quick test made a soldering iron holder bracket, so that I no longer have it wedged in a slightly open bottom draw as I have for the last 5 years.
Few meters of h05rn-f cable to replace the kinked, short, annoying h03vv on the soldering iron. I couldnt find anything more flexible rated for 240v but Im interested if theres a better option.
i used a length of braided cable from an expensive industrial clothes iron. there's no reference number on it, though.
Agroshield
Member
- Messages
- 5,417
This is good. Could not see the spec. though but if you sniff around Antex's site, you might find it.
Antex W021600 1.5m Silicone Lead
Antex - W021600 - Antex W021600 1.5m Silicone Lead - <p>Heat resistant, 3-core silicone cable for soldering irons.</p>
www.rapidonline.com
New tool Thursday. 1p less than 20 english pounds courtesy of a trip to Lidl. Was surprised to find it came in a plastic case with some blades for that price too, was expecting just the tool in a cardboard box. 310w so not sure how that compares to other models but price wise the cheapest I've seen these, elsewhere is usually at least 50 quid.
3 year guarantee too.
3 year guarantee too.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,621
- Location
- Going Away.
A few bits was acquired by me today.
A bit of new, a bit of old and bit of very old.
The site I was on today was in semi darkness.
This was given to me to help. It is very bright.
It certainly showed the mistakes and the mess being shut for 10 months.
Nice little wooden calliper, worn, but still useful for my needs.
A complete Lucas Bicycle lamp.
Needs some TLC, but that's something for me to do.
A bit of new, a bit of old and bit of very old.
The site I was on today was in semi darkness.
This was given to me to help. It is very bright.
It certainly showed the mistakes and the mess being shut for 10 months.
Nice little wooden calliper, worn, but still useful for my needs.
A complete Lucas Bicycle lamp.
Needs some TLC, but that's something for me to do.
Fraserb
Member
- Messages
- 1,562
- Location
- Scottish Borders
8ob
Member
- Messages
- 13,829
- Location
- Nescient in the vale
Oh yes, eat your heart out flaskists
Mine in action
I have a number of a guy that gets them on a regular basis, pm me if you want some
Bob
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,621
- Location
- Going Away.
Oh yes.
This is now MINE.
Jewellers blow torch.
