- Thread starter monkeymark
- Start date
lotus_esprit_s1
Member
- Messages
- 845
- Location
- UK
I had never heard of Beech toolboxes however there is a large double width Beech roller cab top and bottom section in a workshop I have recently purchased. I presumed it was a cheap Snap On copy.
chrisbeee
Member
- Messages
- 90
- Location
- nottingham
You will have to post a pic
Onoff
In the land of the unfinished project I am King!
- Messages
- 11,674
- Location
- Sevenoaks, UK
That sounds absolutely...offal!
These company's definition of what the X% "meat" is made up from I suspect is different to what I think of as meat.
JMS1972
Member
- Messages
- 1,208
- Location
- NW Leicestershire, UK
The squares may have had a base on them. I bought one similar to this when I lived in France its really handy. Setup Square
On this website if image doesn't work flanged-set-up-square
JMS1972
Member
- Messages
- 1,208
- Location
- NW Leicestershire, UK
I think someone has already mentioned this but that looks like the HVLP air compressor from a Flamefast brazing setup. I have one still inside its metal case.Two of these things. I don’t really know what they are (apart for heating torches obviously), but they were part of a pewter casting setup.
The straps on the while cylinders pop off but the stack of discs won’t come apart the just rotate.View attachment 286322
View attachment 286323
View attachment 286324
The left hand wall as you look at the picture faces my garden, so I cleaned up and re-used the bricks that came down from the original back wall so it matches in pretty well, the back wall is against the existing garden wall which is much taller so nobody can see it and the right hand wall faces the neighbours garden, theres a 6ft high fence hence using the poorly matching bricks at the bottom and the better ones nearer the top.
sardine
Member
- Messages
- 3,660
- Location
- Buckinghamshire
I used to get Richmond sausages for free in big catering size boxes but I couldn't eat them, they are disgusting, I left a load of cooked ones out in the garden and nothing ever touched them and they didn't go off they just dried up and went rock hard like bits of rebar.
Arc Tourist
Member
- Messages
- 4,894
- Location
- Wales
Today I collected the 2' x 4' hydraulic lift table. Very happy with the condition, and it was a nice day out for a road trip. 
The paperwork I was given states it is a TDF70 double lift table truck, and was originally sold by Midland Bearings LTD.
The paperwork I was given states it is a TDF70 double lift table truck, and was originally sold by Midland Bearings LTD.
James1979
Member
- Messages
- 8,434
- Location
- Orkney
That’s in good order.Today I collected the 2' x 4' hydraulic lift table. Very happy with the condition, and it was a nice day out for a road trip.
The paperwork I was given states it is a TDF70 double lift table truck, and was originally sold by Midland Bearings LTD.
View attachment 286882 View attachment 286883 View attachment 286884
winchman
Member
- Messages
- 5,874
- Location
- Merseyside
Excellent boxes I have a few, still looking for a Beach side cab only ever seen one, so good info on them on Garage Journal.
Arc Tourist
Member
- Messages
- 4,894
- Location
- Wales
I would say "as new". The add said it had only been used several times, and I can believe that. The sellers were lovely people, and it was a very pleasant transaction.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,627
- Location
- Going Away.
Due to a unforeseen incident I had time on my hands.
So I had an amble round a town and found a great little shop, very nice owner. I hope her venture goes far.
This was what got me inside.
Oh, just another old breast drill.
It is, but with a few things I like.
The twin jaw is designed to take square taper shanks bits. Like the old style Bit and brace drill.
The gearing is also low, so a lot of torque is produced.
This torch is the French version of the Ever ready Space beam torches.
Going to a bit heavy with 8 "D" cell batteries.
A Pair of Lucas Carbide lamps.
So I had an amble round a town and found a great little shop, very nice owner. I hope her venture goes far.
This was what got me inside.
Oh, just another old breast drill.
It is, but with a few things I like.
The twin jaw is designed to take square taper shanks bits. Like the old style Bit and brace drill.
The gearing is also low, so a lot of torque is produced.
This torch is the French version of the Ever ready Space beam torches.
Going to a bit heavy with 8 "D" cell batteries.
A Pair of Lucas Carbide lamps.
cianh91
Member
- Messages
- 734
- Location
- kildare ireland
We had them in the last job and there brilliant bitta kit to have . You will find yourself using it more than you expect . I used ours for fab work because it saved the back on a lot of the jobs I was doingToday I collected the 2' x 4' hydraulic lift table. Very happy with the condition, and it was a nice day out for a road trip.
The paperwork I was given states it is a TDF70 double lift table truck, and was originally sold by Midland Bearings LTD.
View attachment 286882 View attachment 286883 View attachment 286884
Farside
Badly Welded Man
- Messages
- 5,744
- Location
- Ireland
Lips, eyes and rissoles.
ronan
Member
- Messages
- 11,399
MattF
Forum Supporter
- Messages
- 16,608
- Location
- South Yorkshire
Yup.
