Today I acquired...........

[Mick Annick]

There were also two pieces of round bar 35mm x 300mm, one marked

35
63 60

Any idea what it is? I assume it’s hardness?

 

[Blobber]

Nice haul, looks like some good gear^^^

 

[25.4_mechanic]

35
63 60

Any idea what it is? I assume it’s hardness?

What does a file do to it?

Carsten

--

 

[Mick Annick]

What does a file do to it?

Carsten

--

I’m not risking one of my lovely Pferd files on a lump of metal like that!

 

[The_Yellow_Ardvark]

@Arc Tourist makes my little bit look just that.
Little.

 

[The_Yellow_Ardvark]

Taken me all day, to un pack a box I got two weeks ago.
Please bare in mind the box was not given any care in the handling of it.
If I knew then what I new now...........

This is what was in the box.

A right mix of bits.
The most usefull to me are the:
Wire brush, brass gears, hole saw and chain splitter.
The socket is a 1/4 WD Britol socket.

A bit of History.
The tape measure.
The two drill bit holders. one is B&D and the other is Raw Plug. Both have drills is, but I have not looked as yet.


I wonder if they are still going?

YES!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Another one, this one even has liquid inside it.

Then at the bottom was this.

Nice.
I was going to bin the box, the items had been padded with news paper.
Some thing made me poke the paper.

It doesn't fit the lamp, it has a wall thickness of less than 2mm.

Finaly there was this.

YAY. Me one happy Vark, with blood pressure.

 

[Mick Annick]

@The_Yellow_Ardvark

mr Vark, can I ask where you get your hammer handles and wedges from please? I now have 12 hammers that need new ones (and wedges)

 

[DAPPH]

Easy enough to shove a rubber mat in front of the lathe etc., & who doesn't have a doormat for wiping their boots on in their workshop, (or am I alone on that one? )?

I have three very thin 600 x 900 fine knit cut loop type rubber backed slip resist mats in my mancupboard .. Not having them makes my feet and legs ache IIRC they were out of B&M for under a tenner each

 

[The_Yellow_Ardvark]

@The_Yellow_Ardvark

mr Vark, can I ask where you get your hammer handles and wedges from please? I now have 12 hammers that need new ones (and wedges)

I get the hammers shafts them from my local hardware shop. It is cheeper and easier that way.

I have made my own in the past, will do again. But for speed I buy in.

Wedges?
I make my own.

 

[DAPPH]

@The_Yellow_Ardvark

mr Vark, can I ask where you get your hammer handles and wedges from please? I now have 12 hammers that need new ones (and wedges)

When I can afford £300 or so for a new 240v single phase 1/2 hp motor for my lathe I'm hoping to make some out of locally grown ash or white ash .... life is commanding the income for other things at present

 

[Richiew]

Stick a wanted ad on here. I am sure you can get sorted with a motor for much, much less than that.

 

[Arc Tourist]

@Arc Tourist makes my little bit look just that.
Little.

Not quite sure what you mean , but if it is what I think it is, the Wife tells me I can't be sporting the big boy out in public.

 

[My Old Landy]

This is the metal I scored yesterday. Really happy with the sheet but it is far too big for me so after I cut 500mm off the end I offer the rest on here

 

[Maker]

When I can afford £300 or so for a new 240v single phase 1/2 hp motor for my lathe I'm hoping to make some out of locally grown ash or white ash .... life is commanding the income for other things at present

Who's charging three hundred quid for a half horse motor? I'd expect to pay about £100, you could get a three phase one, a VFD and still have change from £300 !

 

[Mick Annick]

I get the hammers shafts them from my local hardware shop. It is cheeper and easier that way.

I have made my own in the past, will do again. But for speed I buy in.

Wedges?
I make my own.

But you have wood bothering skills, unlike me, who has none

 

[Mick Annick]

I also got the anvil up on the stump with the help of a mate and some ratchet straps - it’s marked 110kg. I now need to find some chain now to quieten it down a bit.

 

[RichardM]

who doesn't have a doormat for wiping their boots on in their workshop, (or am I alone on that one? )?

I have one too (the old one from the front door - still get bollocked for getting swarf on the hall mat
Good job I have to walk outside to get in the garage!

 

[25.4_mechanic]

I also got the anvil up on the stump with the help of a mate and some ratchet straps - it’s marked 110kg. I now need to find some chain now to quieten it down a bit.

It is not clear to me how you are going to attach the anvil with a chain, but it is clear that the connection between the anvil and its base is elementary and non-trivial.

This HERE seems to me to be a pretty good solution - the videos of him are worth watching anyway.

Good luck!

Carsten

--

 

[Seadog]

The chain isn't for attachment. It's wrapped around the foot to dampen ringing.

 

[25.4_mechanic]

The chain isn't for attachment. It's wrapped around the foot to dampen ringing.

In that case it would be even more important to watch the linked video, because it works better than with chains and much better than this anvil has been screwed down in the past.

Without proper attachment to the base it will ring terribly even with chains wrapped around - and how does that look btw?