- Thread starter monkeymark
- Start date
A BDSM Bedstead.
W.olly
Member
- Messages
- 3,723
- Location
- Radcliffe, Manchester
Well.today arrived the Driveaway Awning for the van I got a month or so ago. This will be to gain sanity to get the boat done.
Gona find a field.or Park.to practice.while I fit a removable rock n roll amd get gear back together.
Oh and clean my tackle. Not had it out for a while
Gona find a field.or Park.to practice.while I fit a removable rock n roll amd get gear back together.
Oh and clean my tackle. Not had it out for a while
Luggsey
Member
- Messages
- 203
- Location
- Devon
Does that make things rusty?
redlig
Member
- Messages
- 3,632
- Location
- wiltshire uk
I'm told that if used correctly the movement stops the rust forming.
Luggsey
Member
- Messages
- 203
- Location
- Devon
Does rust make it more or less squeaky?
redlig
Member
- Messages
- 3,632
- Location
- wiltshire uk
I don't know about the effects of rust in relation to the noise level of squeaks but it doesn't hurt to use the occasional squirt of lubricant .
sako243
Member
- Messages
- 3,458
- Location
- My mansion in Wales
Some tooling for the G. Dufour mill.
A clear workbench and a working plasma cutter. It was misbehaving a few months back, finally had a chance to look at it a couple of weeks ago and then it stopped working completely, not firing up the arc at all. Checked with a torch from my father's unit and no dice last night so submitted a query to R-Tech (gone 5pm) about sending it back for diagnosis. Had a phone call at about 10am this morning with a technical guy and we walked through the problems and suggested starting with adjusting / calibrating the spark gap thingy (for want of a better word) and told me roughly where it should be and what to look for when it was "good". Went out to the workshop - followed his suggestions and got it working again. Despite what people say about them not bad service for a unit that's 3 years out of warranty and 6 years old.
A clear workbench and a working plasma cutter. It was misbehaving a few months back, finally had a chance to look at it a couple of weeks ago and then it stopped working completely, not firing up the arc at all. Checked with a torch from my father's unit and no dice last night so submitted a query to R-Tech (gone 5pm) about sending it back for diagnosis. Had a phone call at about 10am this morning with a technical guy and we walked through the problems and suggested starting with adjusting / calibrating the spark gap thingy (for want of a better word) and told me roughly where it should be and what to look for when it was "good". Went out to the workshop - followed his suggestions and got it working again. Despite what people say about them not bad service for a unit that's 3 years out of warranty and 6 years old.
James1979
Member
- Messages
- 8,434
- Location
- Orkney
I’ve always had good things to say. Their tech department is very helpful
DAPPH
as dyslexik as I'm daft
- Messages
- 7,012
- Location
- Near to Cross Hands Llanelli SouthWales GB
Vono were makers of metal & wooden framed bolt up yourself joints on their beds , I've not seen any with extended bolts and wing nuts & pads before , if these are originals could they be part of a leveling up set up ?
Could they be the levellers /reinforcing for this Vono bed ?
Vono double stacked bunk beds I suspect which need tightly pulling together. Many an army barracks had them.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
Ex Boss had to admit that the drkill that was in my old van did not belong to the company.
So he had no choice to buy me a replacement.
Had to, as when they emptied the van for the stock take, they wrote the drill off and binned it
Shox Dr
Chief Engineer to Carlos Fandango
- Messages
- 17,993
- Location
- East Yorkshire
I dont thonk you can bear Ryobi One Plus gear. Its taken me 12yrs to let the smoke out of one, and that was been hard on it.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
It replaces the Old Bosch one I had
Hopefuldave
Intergalactic pot-mender
- Messages
- 2,545
- Location
- The Shed of Danger, surrey, England
Mine is too - was a sod getting it in and out of a Transit Connect, though...Its great to see a machine with an "undamaged" table.
Still got to sort a new control box, mashed before I got it!
Dave H. (the other one)
Auxiliary handle simply impossible to clean and make look new? First thing my father removed when he purchased a new tool.Did it again
Won an eBay auction , well I've actually placed an offer not a bid
View attachment 393698the seller accepted so I've actually bought this "faulty" Metabo WEA 24-230 MVT for 50 euros . Pretty confident by looking at the conditions that the only fault is the broken plug. I already have Metabo tools and auxiliary handles are simply impossible to clean at the point to look new . This one looks little bit dirty but the overall plastic and gear housing conditions make me think that it has worked for very little time prior somewhat happened to the plug . It features ,soft start,anti restart protection,electronic safety clutch, overload protection,antivibe handles, autobalancer, four positions swivel main handle. I have a protective guard might fit , and i might have to buy a quick release nut as the original one has been either lost or taken off the grinder. Always wanted one of those but 350 euros for a grinder was really too much. I'm still hunting for deals
Bullet2012
Member
- Messages
- 4,927
- Location
- 238 855 miles from the moon
Not acquired , but up for sale if anyone fancies a new toy!
RAF Scampton: Jet flown by Red Arrows goes up for sale
The plane was flown by the famous team for 32 years before acting as "gate guard" at RAF Scampton.
www.bbc.co.uk
slim_boy_fat
Forum Supporter
- Messages
- 29,540
- Location
- Scottish Highlands
^^ Forum buy? 
Hopefuldave
Intergalactic pot-mender
- Messages
- 2,545
- Location
- The Shed of Danger, surrey, England
Do we get it on our front lawn for a week a year? I could be up for that...^^ Forum buy?
Dave H. (the other one)
