Today I acquired...........

[dobbslc]

It's going to be a present for my BIL as he's just bought himself a 1945 Willys Jeep!
The thing looks like it was stored on a sunken aircraft carrier.....

 

[The_Yellow_Ardvark]

Today I acquired a position to become a Fire alarm engineer.
I am now back to 6 positions not filled.

My engineer who was mentioned in Post #5702 has just E mailed everyone that he is leaving.

30 minutes ago I ran the daily tracker report, his van is located in a Police station. A few phone calls found out why.

Being followed by a Police car, he was on his phone. Phone records can prove it, plus he admitted to it. When they used the "Blues and two's" he drove into a skip.

I wonder what was in the skip what would of been of use.

He has been charged already, no details as yet on what.

So, as his termination E mail was received after his "incident" was he technically employed by us?

This is going to be a admin nightmare.

 

[slim_boy_fat]

So, as his termination E mail was received after his "incident" was he technically employed by us?

Imo, it would depend on a) when the email was sent [NOT received] and b) when the crash happened.

That's the attitude!!

 

[Chillitt]

Just before the Great trailer Rebuild, I found these. Looks like the new plan might have ramps stashed under the floor. Stylish!

 

[DAPPH]

This
View attachment 117770
A pot of bees wax, turpentine and linseed oil premixed ready for use on this,
View attachment 117771
A 1944 pick axe resto!

That's a mattock rather than a pickaxe surely ?

 

[dobbslc]

I don't know. It's made in the USA though, do they have mattocks over there?

 

[gordon stephenson]

Dodge 20, Where's your British Dunkirk spirit man, Dig for victory.

 

[bigegg]

Imo, it would depend on a) when the email was sent [NOT received] and b) when the crash happened.

That's the attitude!!

Hopefully the crash and the email weren't concurrent?
And I think (1) that until his notice is accepted, he's still employed.

(1) it doesn't happen often - just go with it.

 

[Wedg1e]

Same year I was born, It'll be a good un!! ( Even better after a little TLC,)

Do you come up well after a rub with some wax then...?

 

[slim_boy_fat]

And I think (1) that until his notice is accepted, he's still employed.

Aye, and will still be technically 'working his notice' unless, of course, he'd been 'terminated with extreme prejudice'........

 

[gordon stephenson]

Ian, A rub with anything would be very welcome, Can nursie recommend anybody that does "bed baths "?

 

[Dodge20]

Dodge 20, Where's your British Dunkirk spirit man, Dig for victory.

I would but I kind of value my current state of aliveness.

 

[brightspark]

Ian, A rub with anything would be very welcome, Can nursie recommend anybody that does "bed baths "?

 

[God mode restorations]

Today I acquired this nice little precision level to level my lathe ECT.

 

[eLuSiVeMiTe]

Today I acquired this nice little precision level to level my lathe ECT.View attachment 117806

Been looking at levels for the same reason. If you don't mind me asking how much where from and opinions.

 

[God mode restorations]

Been looking at levels for the same reason. If you don't mind me asking how much where from and opinions.

It's a 100mm long. £72 in total. RGD tools. It's nice. Heavy but very accurate.

 

[Arc Tourist]

The shorter precision level's can be set on a long parallel if increased length is needed.

 

[God mode restorations]

I did a test. I used my fat max level to get lathe level. I put the precision level next to it. Am out by a fraction.

 

[Seadog]

Did you turn your Fatmax level round to verify that it's reading true?

 

[angellonewolf]

^^^^^ i got 5 levels they all say differant angles