- Thread starter qwakers
- Start date
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
This wee one just needed a clean of all the crud, a light oil and a good waxing.
Onoff
In the land of the unfinished project I am King!
- Messages
- 11,625
- Location
- Sevenoaks, UK
A picnic bench up the pub. Some foaming Gorilla and 5x90 A2 screws. A bit long so the pointy ends zinged off with the 18V Fakita where they poked through.
Forgot to take a picture so will have to go back tomorrow...
Forgot to take a picture so will have to go back tomorrow...
jsf55
Member
- Messages
- 1,565
- Location
- Sunny Swansea
Evap canister blocked or purge valve similar. So went and changed both this afternoon. Found boot full of water while playing find the locking nut tool. it was drilled after i got the wheel off with the aid of the big rubber mallet, cleaned and copper slipped, it was tight in there but no codes after a reset and run out 
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
Here was power tools from the long weekend.
Maker
Most folk just call me; Orange Joe
- Messages
- 10,487
- Location
- Don't ask questions
We've all been there.
Might not have needed them if the house has them in the consumer unit?
I find a choccy-block connector about a foot down the cable saves time . . . jams the blades before severing everything
an extra RCD won't hurt on the extension. We prefer not to put chock blocks in as there is no strain relief on them. If we think that the cable will end up too short, the whole cable gets replaced and then PAT tested,
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
Not me. I was just tech support and a quiet place supplier.
Theses two grinders were donated to us, the red one ended up being placed into the spares bin
The B&D was inspected, logged in and we choses to give it a go at getting it working.
Instant fail.
As we try to promote good working practice, we don't even power this up, until the damaged is fixed.
I had already tested this tool, so i knew it worked, but with the member we followed the safe way.
This is the switch, first impression that is one of the classic B&D sealed units. But I knew differant.
It does mean more stripping down.
Lift up the suppression capacitor and expose theses 2 connectors.
The switch can be slid out. Pop of the plastic cover and the 2 screw connections are exposed.
Then you can re-wire the switch.
Repaired, PAT done, guard fitted and now ready to be used.
Theses two grinders were donated to us, the red one ended up being placed into the spares bin
The B&D was inspected, logged in and we choses to give it a go at getting it working.
Instant fail.
As we try to promote good working practice, we don't even power this up, until the damaged is fixed.
I had already tested this tool, so i knew it worked, but with the member we followed the safe way.
This is the switch, first impression that is one of the classic B&D sealed units. But I knew differant.
It does mean more stripping down.
Lift up the suppression capacitor and expose theses 2 connectors.
The switch can be slid out. Pop of the plastic cover and the 2 screw connections are exposed.
Then you can re-wire the switch.
Repaired, PAT done, guard fitted and now ready to be used.
Thanks for that @The_Yellow_Ardvark If we get one in, I'll know what to look for now.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
As other things were going on, it was decided to fix this grinder. This is one of mine, I just had not got round to repairing it.
Well, that's not good.
The crimps are sealed with some gunk.
The blue cable was covered in a hard substance
The Brown was covered is something like silicon.
Removing it proved the blue cable was Open circuit.
Take note of the way the cables are routed and how the cable clamp is fitted.
Not how to do it.
Before final assembly I made sure it clipped in place.
All working.
There was more than a hint of
in my choccy block suggestion 
I hope you recommend the additional RCD is plugged into the fixed socket, and the extension into it, rather than it plugged into the extension?
A neighbour at my last house used to use a really slow B&D decker drill powered hedge trimmer - he didn't bother with the chopping of the cable . . . went straight for the thumb
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
Not today, but the large amount of the work was done on Friday.
This came my way, it looked good, if a bit rusty.
How ever when stripping it down a big issue came to light.
It had been dropped.
The handle fixings were bent, but could be straightened. But the body was warped.
So we took it to a friends garage, who has a surface grinder.
A few pass's had the sole flat, a few more had the side at 90 degs and a nice finish.
The blade and caps were also done at the same time.
Assembled and now a nice addition.
This came my way, it looked good, if a bit rusty.
How ever when stripping it down a big issue came to light.
It had been dropped.
The handle fixings were bent, but could be straightened. But the body was warped.
So we took it to a friends garage, who has a surface grinder.
A few pass's had the sole flat, a few more had the side at 90 degs and a nice finish.
The blade and caps were also done at the same time.
Assembled and now a nice addition.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
This was from a Nice member on here.
It has already proved its worth, but did open a debate.
Does it need to be given a PAT?
The short answer is:
Yes.
So we gave it one. Cleaned it up and mounted it on the wall.
It has already proved its worth, but did open a debate.
Does it need to be given a PAT?
The short answer is:
Yes.
So we gave it one. Cleaned it up and mounted it on the wall.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
Yesterday was a busy day, a lot going on.
Lots of coffee drank, bread made and stuff fixed.
This is a few of the things we fixed, repaired, cleaned up and got working.
I chose theses items, as I have posted the images here.
The wooden box was part of a collection, the compass should not be there.
Rusty gramophone needles.
Needles de rusted, box polished and the insides given a few coats of Linseed oil.
We take cleaning up of tools as run of the mill. But some never have done it.
So this was used to show a new member that something they thought was only fit for the bin, could be saved and put to use.
Just using hand tools, hard work we have a nice small clamp.
Power tools can scare people, but there are ways to allow them to join in.
This Hacking knife was complete, but the cutting edge was blunt.
The leather was fed, then we put an edge on the blade.
Not with an oil stone, that needs a bit more tuition.
Lots of coffee drank, bread made and stuff fixed.
This is a few of the things we fixed, repaired, cleaned up and got working.
I chose theses items, as I have posted the images here.
The wooden box was part of a collection, the compass should not be there.
Rusty gramophone needles.
Needles de rusted, box polished and the insides given a few coats of Linseed oil.
We take cleaning up of tools as run of the mill. But some never have done it.
So this was used to show a new member that something they thought was only fit for the bin, could be saved and put to use.
Just using hand tools, hard work we have a nice small clamp.
Power tools can scare people, but there are ways to allow them to join in.
This Hacking knife was complete, but the cutting edge was blunt.
The leather was fed, then we put an edge on the blade.
Not with an oil stone, that needs a bit more tuition.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
Oh yes.
I fixed the swing compass.
I fixed the swing compass.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,614
- Location
- Going Away.
This Hanging Light pendant was mine, so it, with another item was used to teach members that brass cleaning id not hard work or dull.
Along with this Brass Barn Tin.
But the tin had an issue.
Oh well.
Brass cleaning solution.
Cleaned.
The broken steel pins were drilled out, then using a brass nail, new hinge pins were made and fitted.
