Stuff you have made today

[mtt.tr]

That's some 'beaver'. My beaver moves itself, but complains a lot. Also looks like 'your beaver' has taken your balls. Fortunately I've still got mine

She's a hungry beaver

Gets better the original manufacturer was Balding engineering

So I have a balding beaver

 

[Westfield-builder]

So I have a balding beaver

My favourite type

 

[DAPPH]

I’ve used some oil soaked paper wrapped around the shaft for the seal to slide on, once it’s in position the paper pulls out.

Plastic drink cups were often use on our fleet of mini's for the slipping of seals over on shafts ..plenty of grease on the seal & cup . various thin plastic pop bottles carefully cut in half can also be helpful in the same exercise.

 

[Kram]

A @Munkul inspired 8mm boring bar sleeve. It was interesting to get a 7mm bar to cut a tight 8mm bore. Using up some en3b as I dont imagine the grade making any difference for this.
I just found a peice of 27mm cast iron, I cant think of any better use and I need to make a few more, 8.4, 10, 12 and 13mm.

 

[northwest]

Well I finaly finished one of those projects, first spotted on here and i thought "I can improve/make one of those, for my new improved MkII Tig welding bench, the swing out seat yet to come. Error No1 Snap the tap:

Drill it out:


Being slow in the "learned my lesson" department I then went at it and did it again, didn't think I would get away with drilling it out a second time but to my amazement I did. Not made the thumbscrews yet, but I will, eventually. Works a treat:



t is bolted to a realy hefty bit of plate welded to the bench which is drilled and tapped.
The post is a bit of EN something or other that I made into a bearing holder, I dismantled the original swing arm bit and fitted a couple ball races:

it all appears to work well and should stop me scrabbling about for "Bits of stuff"to use as a support and take some of the jerkiness out of my welding, we will see.

 

[henry Kadzielski]

drilling it out a second time

I have never been able to remove a tap by drilling. I use Dormer drills and they won't touch a Dormer tap. I have even tried a carbide drill to drill a broken tap in stainless steel, still didn't work. 'Electra' (EDM) on the other hand works a treat.

 

[Hood]

I have never been able to remove a tap by drilling. I use Dormer drills and they won't touch a Dormer tap. I have even tried a carbide drill to drill a broken tap in stainless steel, still didn't work. 'Electra' (EDM) on the other hand works a treat.

You really need something rigid such as a milling machine to make the drilling successful, obviously it requires carbide though. I usually just use a carbide milling cutter rather than a drill.

 

[123hotchef]

I saw a trick to remove the broken taps with a split pin

 

[123hotchef]

Remove a Broken Tap

ace240z.com

I aint tried it though

 

[northwest]

I have never been able to remove a tap by drilling. I use Dormer drills and they won't touch a Dormer tap. I have even tried a carbide drill to drill a broken tap in stainless steel, still didn't work. 'Electra' (EDM) on the other hand works a treat.

That is a good quality Carbide Drill and the job is set up in the Mill.

 

[northwest]

I saw a trick to remove the broken taps with a split pin

none, absolutely none of these "tricks" or as they are now called "Life Hacks" have EVER worked for me, I use German technology: Brute force and ignorance, that always works. Going outside shortly to adjust the cabinet stand on the Conect, Angle Grinder at the ready, I would use the plasma if I thought it would work but I am not convinced so the tried and tested way for me today.

 

[Dr.Al]

Well I finaly finished one of those projects, first spotted on here and i thought "I can improve/make one of those, for my new improved MkII Tig welding bench, the swing out seat yet to come. Error No1 Snap the tap:
View attachment 321827
Drill it out:
View attachment 321828

Being slow in the "learned my lesson" department I then went at it and did it again, didn't think I would get away with drilling it out a second time but to my amazement I did. Not made the thumbscrews yet, but I will, eventually. Works a treat:

View attachment 321827View attachment 321828View attachment 321829View attachment 321830View attachment 321831View attachment 321832View attachment 321833

t is bolted to a realy hefty bit of plate welded to the bench which is drilled and tapped.
The post is a bit of EN something or other that I made into a bearing holder, I dismantled the original swing arm bit and fitted a couple ball races:
View attachment 321835
it all appears to work well and should stop me scrabbling about for "Bits of stuff"to use as a support and take some of the jerkiness out of my welding, we will see.

That's gorgeous and a lot classier than my effort!

 

[Barking Mat]

Assembled a new rudder for a client, mild steel with stainless rudder shaft. Skeg got attention too.

Some tidy welds too...

 

[Hood]

I shouldn't like that ^^^
It is one of my pet hates, stainless and steel arrrrrrrrrrrrrrrrrggggggggggggghhhhhhhhhh

 

[Barking Mat]

I shouldn't like that ^^^
It is one of my pet hates, stainless and steel arrrrrrrrrrrrrrrrrggggggggggggghhhhhhhhhh

It's a canal, last ones done thirty years.

Think calm thoughts....

 

[123hotchef]

It's a canal, last ones done thirty years.

Think calm thoughts....

I bet the canals are still a bit salty up near you aint they?

 

[Barking Mat]

I bet the canals are still a bit salty up near you aint they?

No, they're all fed from rivers.

The Vilaine river is affected by the tide, with sea water going up to Redon, but the rest is freshwater.

Fiberglass boats generally.

 

[Hood]

It's a canal, last ones done thirty years.

Think calm thoughts....

Ha ha it is just the fact that stainless is welded to steel

 

[Barking Mat]

Ha ha it is just the fact that stainless is welded to steel

Used my best (whatever I could find 316 rods), works for me.

Always done it like that.

What do you dislike ?

I'm not a pro, oh no...

 

[Hood]

Nothing wrong with what you have done except I just hate stainless and steel being mixed