Today I acquired...........

[Turbo]

I recently took delivery of these Swallow 15x80 porro binoculars that I bought via facebook!

The smaller set is my Nikon 8x42 roof prisms for comparison

I think the tripod will be needed for extended viewing!!


John

Those would be great for star gazing if you build a parallel arm mount.

 

[stuvy]

Collected it yesterday but got a bargain from eBay £12 chopsaw that’s hardly used

 

[Pete.]

You might have notice me selling off a few bits recently. Well, the reason for that has just arrived - a DRO to go on my Monarch lathe

 

[Geoffm]

Went for this in the end. Partly on Geoff's recommendation, I think it is the same family of drives. Hope it is OK. Made sense to sort the issue in one go rather than get a 240 vfd (Which would have been cheaper initially but a waste in the long run) and lose the top end speed on the mill and have to get another motor at a later date to get full use.

https://uk.banggood.com/220V-To-380...sc_uid=COcBkF10nm&ID=6138292&cur_warehouse=CN

I can always repent at leisure, let's hope HMRC are making a cup of tea as it passes through.

Should do the job. I dont think I have changed the belt settings on the RF30 since I put the VFD on. Make sure you get the manual. There are a few settings you will need to set e.g. if you are using remote switching or speed pot. I used the original on / off switch to remote switch the VFD.
I am looking at putting a VFD on my Daishin Prince lathe as the bottom speed is more than I like for threading.

 

[dobbslc]

Got a nice Facom hacksaw from an autojumble on Sunday.
£3

 

[DAPPH]

Got a nice Facom hacksaw from an autojumble on Sunday.
£3View attachment 206011

That's a bargain .........…. as the basic one is about £20 when new.

 

[dobbslc]

I had one years ago and the sparks son I was working with borrowed it and used it as a hammer and snapped the blade locating stud off it!
I only found out after he went back to Cornwall luckily for him.....

 

[sardine]

Hacksaws always give me flashbacks to when I was an apprentice and the powered hacksaw machine broke , I was handed some 3 " steel bar and told to start sawing.

 

[The_Yellow_Ardvark]

Swopped for some beer I was given over the silly season.
Bloody terrible stuff.

My friend couldn't get on with it.

 

[Johnnybravo]

View attachment 206013

Swopped for some beer I was given over the silly season.
Bloody terrible stuff.

My friend couldn't get on with it.

In my experience those silly little soldering guns are enough to make anybody hit the bottle..Despicable things....

 

[The_Yellow_Ardvark]

In my experience those silly little soldering guns are enough to make anybody hit the bottle..Despicable things....

It is the second one I have.

For circuit board repairs, cable joints they are a pig to use.

For copper wire art work, small lap joints in brass and similar they are not bad.

 

[bigegg]

It is the second one I have.

For circuit board repairs, cable joints they are a pig to use.

For copper wire art work, small lap joints in brass and similar they are not bad.

good as a hot wire cutter for foam, as well.

 

[Wedg1e]

It is the second one I have.

For circuit board repairs, cable joints they are a pig to use.

For copper wire art work, small lap joints in brass and similar they are not bad.

... and soldering together multitudinous wires under the dashboard when fitting car alarm systems (previous job of mine). Remember to put the heatshrink over the wires first
Just don't drop the hot end on the carpet of the new BMW you're working on, as the guy I worked for did

 

[eLuSiVeMiTe]

Plastic welding too. :/

They are useful for heavier work.

 

[Johnnybravo]

Plastic welding and foam cutting then. Anything that doesn’t involve solder

 

[EddyP]

You might have notice me selling off a few bits recently. Well, the reason for that has just arrived - a DRO to go on my Monarch lathe

View attachment 205888

Looks good Pete, where did you get it from? eBay? I'd love a DRO on my chipmaster but suspect I'll struggle to justify the cost.

 

[Memmeddu]

Looks good Pete, where did you get it from? eBay? I'd love a DRO on my chipmaster but suspect I'll struggle to justify the cost.

There are a lot of single axis dro on AliExpress for cheap
You have to zero them while changing the tool but you still have a digital reference

 

[northwest]

Looks good Pete, where did you get it from? eBay? I'd love a DRO on my chipmaster but suspect I'll struggle to justify the cost.

I struggle to understand your struggle. If you see what I mean. DRO on a lathe transforms your repeatable accuracy. Also significantly increases your speed at doing a job. A real plus for me.

 

[Pete.]

Looks good Pete, where did you get it from? eBay? I'd love a DRO on my chipmaster but suspect I'll struggle to justify the cost.

Yes ebay, ValueDRO. It was £299 and sent from the UK.

 

[Fraserb]

Not the usual stuff you aquire, was sorting through the random scrap pile and you don't half aquire some odd shaped cut offs.