Onoff
In the land of the unfinished project I am King!
- Messages
- 11,717
- Location
- Sevenoaks, UK
No, but you could likely print the plates to print the notes with, e.g:
Whole new world isn't it!
- Thread starter Parm
- Start date
No, but you could likely print the plates to print the notes with, e.g:
Whole new world isn't it!
MattF
Forum Supporter
- Messages
- 16,647
- Location
- South Yorkshire
Cheers Dev. 
This is what it was printing last night.
That unsupported bed cable seemed the best starting point. That print needed a tad of knife & file work to tidy it up, (the inside of the upper cable tie guide sagged a tad), but I'm quite happy with its first ever print.
I can see I have a learning curve in front of me though.
This is what it was printing last night.
That unsupported bed cable seemed the best starting point. That print needed a tad of knife & file work to tidy it up, (the inside of the upper cable tie guide sagged a tad), but I'm quite happy with its first ever print.
I can see I have a learning curve in front of me though.
AndersK
Member
- Messages
- 1,490
- Location
- Sweden
Cura will show you overhangs that need support if you enable that in the config.
The red areas are unsupported geometry. As you can see not the whole hole feature is red and thats based on the slope. Lots of settings in the support section to control this.
In settings, the display overhang and Auto drop are useful
The red areas are unsupported geometry. As you can see not the whole hole feature is red and thats based on the slope. Lots of settings in the support section to control this.
In settings, the display overhang and Auto drop are useful
Bullet2012
Member
- Messages
- 4,940
- Location
- 238 855 miles from the moon
Are the new notes not plastic and polymers ?
Parm
Respect The Sound System
- Messages
- 17,879
- Location
- Towcester
Steady old chap, gimme a chance. Let me have a little play before the fifties start comming off.......
Bullet2012
Member
- Messages
- 4,940
- Location
- 238 855 miles from the moon
Fives will be ok for me
Pete.
Member
- Messages
- 14,388
- Location
- Kent, UK
Creality slicer IS cura actually.
Thanks for that - I was thinking I would download Cura to try it out, but obviously I don’t need to If they are the same. My software was on the usb stick that came with the machine (Ender 3 pro), along with all the build instructions and sample files.
Its had a lot of use in the last couple of weeks as I’m building a laser cutter - printing clips, mounting blocks for micro switches and pcb’s etc. Very useful.
A question - I use Fusion360 for all the design work. Has anyone tried generating the g-code successfully within Fusion? The only time I tried it, the code tried to send the print head off the top of the Z screw at the end of the print. Since then I’ve just exported my design as an stl file and put it into the slicer to get the g code.
Pete.
Member
- Messages
- 14,388
- Location
- Kent, UK
Ah, the creality slicer on my stick was very outdated I had to go to the creality website for the newer version. (Mind you the original version on the stick easily printed Collada DAE files as produced by Sketchup 14 so for THAT it's very useful - if you use sketchup it'll allow you to draw and print models very easily). If you download the newer creality slicer it'll over-write the original old one off the stick and then it doesn't like the DAE files so much.
For the very latest version of cura go to the Ultimaker Cura site.
For the very latest version of cura go to the Ultimaker Cura site.
Parm
Respect The Sound System
- Messages
- 17,879
- Location
- Towcester
Easier to spend in the boozer
Bullet2012
Member
- Messages
- 4,940
- Location
- 238 855 miles from the moon
Ha yes one per beer
MattF
Forum Supporter
- Messages
- 16,647
- Location
- South Yorkshire
You wouldn't happen to have the gcode file you used for that printhead cable strain relief still knocking about, would you?
AndersK
Member
- Messages
- 1,490
- Location
- Sweden
Be careful using gcode from other sources.
It must be generated for exactly the same machine and set-up, like nozzle size and material. Better get the 3D data and slice it yourself.
Edit: the project file is the best .3MF, then you get 3D plus all settings from the slicer. Then just change what's needed to fit your set-up and slice.
Last edited:
MattF
Forum Supporter
- Messages
- 16,647
- Location
- South Yorkshire
Good point. Never thought of that.
brewdexta
The biggest tool in the box
- Messages
- 5,609
- Location
- UK
Do they come with a psu, or do you have to buy that seperately?
Quite liking this enclosure. The industrial look.
Pi-Box Pro 4 Case (with SD access) [Discontinued]
The Pi-Box Pro 4 is a rugged industrial aluminium* enclosure kit for the Raspberry Pi 4. If you need a tough enclosure for your application, look no further! By utilising a micro-HDMI Pi4 extender board, the power and micro HDMI are located at the rear of the case alongside the Ethernet and USB...thepihut.com
I prefer the aluminium heatsink cases like this, cost about a tenner and available from lots of places.
If your adding a daughterboard like a PoE hat then possible not the best option but for Octoprint they are fine. It also means you can hang them off a DIN rail like this, and replace the annoying wall warts with a single 10A Meanwell PSU for 4 x pi4, possible more.
The two rpi4 on the left have 2.5" SSD attached. The PSU is attached to the UPS on the left. There is another pi below that has a one-wire temp probe hat on it, a pi3b I believe, its in a crappy plastic case, that should fit on the rail too soon. I only moved the two rpi4 on the right on to the din rail yesterday.
What am I doing with all these you may ask? Tinkering is the answer. I have pi-hole running on a couple of them, this is a DNS blocker so excludes ads, trackers etc. I also run nagios, Zabbix and a few other network management tools. The ones with SSD are for me to play with virtualisation and containers as I'm doing more of it at work and being a manager get little time to play with the tech.
indy4x
Forum Supporter
- Messages
- 3,253
- Location
- Pontypool, South Wales. UK
Should have the STL, will dig it outYou wouldn't happen to have the gcode file you used for that printhead cable strain relief still knocking about, would you?
