Stuff you have made today

[Memmeddu]

Started "restoring" "refurbishing" few CEE sockets
Cleaned
Painted in white after masking the plate
Painted the 0 in black and the 1 in red

 

[sg66]

Over the hols I went out the side gate and discovered the right hand post was snapped clean through, good job i was on holiday, not.

All joints were made with circular saw, not the best for the job but everything else useful was not at home with me.

 

[eLuSiVeMiTe]

Over the hols I went out the side gate and discovered the right hand post was snapped clean through, good job i was on holiday, not.

All joints were made with circular saw, not the best for the job but everything else useful was not at home with me.

Amazingly useful tools skillys

 

[mtt.tr]

Amazingly useful tools skillys

i use mine for allsorts would be lost without it, especially my worm drive saw can use that with a good deal of control

 

[eLuSiVeMiTe]

i use mine for allsorts would be lost without it, especially my worm drive saw can use that with a good deal of control

Just popped my 110v plane and skilly back in the van. Cordless is great for odds and sods but when your ripping 20 boards.
Getting fed up of caining batteries

 

[mtt.tr]

Just popped my 110v plane and skilly back in the van. Cordless is great for odds and sods but when your ripping 20 boards.
Getting fed up of caining batteries

my only exception is the flexvolt will do alot off cuts, but its not a good framing saw

 

[sg66]

The left post is bolted to the house and the drive, used saw ro recess the post bracket.

 

[eLuSiVeMiTe]

The left post is bolted to the house and the drive, used saw ro recess the post bracket.

Polish plane.

Always keep the nose in contact

 

[mrsbruce]

Finished the desk today. Toned down the edging (still looks very light in the picture, though), and added a metal back piece (an old wardrobe handle out the ‘useful one day’ box). Used some lovely little 7mm length brass domed pins to help hold down the wood edging, just to finish it off.

I’m quite tempted to do a bit gold leaf pattern stamping about 2-3cm in around the edge of the leather. Haven’t used gold leaf for ages, should be fun, and will kill the ‘sea’ of leather. The patterning in the leather looked better in real life, though.

Back to welding tomorrow (yippee!).

 

[mm289]

More progress on the bandsaw, dissasembled and cleaned up the saw itself


Then put the stand in primer and topcoat.



And finally started reassembly


Will order some new bearings tomorrwo, but seem to be missing a part, I think there should be a second retaining bracket for the spring tensioner?


Cheers,

MM

 

[Chillitt]

Mark 2 head now with coat hangers. Not finished yet but getting there.

 

[The_Yellow_Ardvark]

@Chillitt

Top work there.
Hats off to you, we need a mega like button.

 

[gordon stephenson]

Great, Looking forward to the finished item

 

[Memmeddu]

Repaired a Rioby R18sds drill ,a Bosch CSB550RE drill ,a Bosch GWS6-115 angle grinder for customers
Converter a bench grinder from 380V to 220V for me

 

[Dr.Al]

Today I was making some more progress on a replacement switch housing for my bandsaw. While I was doing it, I tightened up the z-axis on the mill (which I usually do when I'm milling) and the handle snapped off in my hand. I hadn't even tightened it up that much.

I carried on with the job (tightening the handle with a pair of pliers), but once it was done I decided I needed to do something about the handle (the scratch marks you can see on the handle body are from the pliers I was using as a temporary tightening method):

Dismantled:

A rotary broach is on my ever-increasing list of things to make but I haven't got there yet, so it seemed like too much hassle to try to make a replacement handle for the existing screw. The design (that can be indexed round thanks to the spring and short hex section) is mainly there due to the restricted access on the x-axis and y-axis. Those haven't broken (yet) and the access restrictions are somewhat different on the z-axis.

So I decided to make a one-piece version instead:

It's made up of three parts: the body (turned and single-point threaded from 20 mm EN1A), the arm (8 mm silver steel with a flat filed half-way along) and an M5 grub screw to hold the arm in place. The only reason I used silver steel for the arm was that I had a piece that was the right length already and it saved effort. The rounded end was made with a file (while the work was spinning in the lathe) before cutting the thread. Probably would have been quicker to use a die to cut the thread, but I quite enjoy single-point thread cutting and it saved digging in the drawer for the right die size, so what the heck.

Here it is in place:

You can't see from the photo, but there's about 5 mm clearance between the arm and the angle scale when the screw is tightened.

 

[northwest]

Bit further on with the Box Pan Folder:

 

[Tupers]

I’m done with my self imposed Christmas break so got on and mitred some C channel and tacked it together for my 250x125cm welding bench.

Legs on tomorrow then I need to figure out how to get a 15mm thick sheet of steel off a truck and onto the frame.

 

[Tangledfeet]

Not really made, just a bit of welding. Pupil drilled a hole (partially my fault) where there shouldn't be one so rather than have him restart I took it home to 'undrill' the hole with the TIG.

 

[stuvy]

Had to tweak the rear end of the car I’m working on so made a little dolly to slide under the steel skin onto the Ali one

Ended up moving it almost 10mm

 

[Yamhon]

I’m done with my self imposed Christmas break so got on and mitred some C channel and tacked it together for my 250x125cm welding bench.
View attachment 206774

Legs on tomorrow then I need to figure out how to get a 15mm thick sheet of steel off a truck and onto the frame.

Are those things in the corners acting as squares or do they have another purpose too?