Tupers
Member
- Messages
- 947
Yes I’m going to be on a long shelf with 6 holes in it so I can have it mounted to a wall but easily pull rods out when I need them.
- Thread starter God mode restorations
- Start date
badabec
Forum Supporter
- Messages
- 1,940
- Location
- Essex UK
What is a mackerel stripper box?
badabec
Forum Supporter
- Messages
- 1,940
- Location
- Essex UK
Thank you, now in my basket..
selectedgrub
Member
- Messages
- 3,327
- Location
- New Zealand
More of the same
I made the lead on the grinder shorter (again and made my foot hurt. I had 56 75cm lengths of 25mm box clamped together and stood up for 'levelling' and I'm not sure what happened next, but they were on the floor, the trip had gone, and my foot is a little sore.
Memmeddu
Member
- Messages
- 4,794
- Location
- Italia Sardegna
Today after many days of history (exactly 15 months) I've eaten some marinara anchovies 
Unfortunately I can't eat them since I've discovered my kidneys problems but once a year would not hurt
I'll probably need to drink water till tomorrow
Unfortunately I can't eat them since I've discovered my kidneys problems but once a year would not hurt
I'll probably need to drink water till tomorrow
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,655
- Location
- Going Away.
I made the lead on the grinder shorter (again and made my foot hurt. I had 56 75cm lengths of 25mm box clamped together and stood up for 'levelling' and I'm not sure what happened next, but they were on the floor, the trip had gone, and my foot is a little sore.
I would laugh, but I feel your pain.
I have spare cable............
Grinder is fixed. Foot is a bit red...
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,655
- Location
- Going Away.
Are you turning Russian Comrade?
3000alloy
Member
- Messages
- 159
- Location
- Ireland
Well got this up over the past week on and off because of rain and other commitments.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 19,655
- Location
- Going Away.
A cloud.
We liked it.
DennisCA
Member
- Messages
- 1,969
- Location
- Finland
Made, no modified this DRO so it would work with the new scale which was of a different pitch and it measured everything twice as much as it had traveled. Heidenhain support provided the procedure info, pretty good tech support since the DRO is from 1979.
Installed, tested and it works! Example, went to 3mm on the DRO and verified against dial indicator I had also zeroed, both show 3mm.
Don't look at the small dial for this, I both preloaded and zeroed the dial indicator at an arbitrary point so what I was really looking for was that the needle landed on 0.
Finally I have a working DRO for both X and Y on my mill. Someday I will get an XYZ DRO and move this one to the lathe.
Installed, tested and it works! Example, went to 3mm on the DRO and verified against dial indicator I had also zeroed, both show 3mm.
Don't look at the small dial for this, I both preloaded and zeroed the dial indicator at an arbitrary point so what I was really looking for was that the needle landed on 0.
Finally I have a working DRO for both X and Y on my mill. Someday I will get an XYZ DRO and move this one to the lathe.
badabec
Forum Supporter
- Messages
- 1,940
- Location
- Essex UK
If you do put it on a lathe, you may have to cut the added wire or you'll be taking 6mm off the diameter instead of 3mm
slim_boy_fat
Forum Supporter
- Messages
- 29,540
- Location
- Scottish Highlands
So today I thought I would see how it went with the stick welder, it has been a long time since I stick welded 1.5mm stainless so was thinking it may have been a bad idea but no, it went well and I had all 5 pipes stuck in place in the time it would have taken me to do one side of one with the tig
Top work!! Is there anything you can't do?
Good job, but aren't you afraid someone might trip heading for the steps and impale themselves on those ends?
Hood
I am obsessed.
- Messages
- 17,315
- Location
- Carnoustie, Scotland
Top work!! Is there anything you can't do?
Aye, stop spending, I find that impossible
Hood
I am obsessed.
- Messages
- 17,315
- Location
- Carnoustie, Scotland
Oh and painting, rubbish at thatAye, stop spending, I find that impossible
No,they’re horizontal and radiused,if they’d have continued in a normal manner,there’s always an end with a railing(usually).Top work!! Is there anything you can't do?
Good job, but aren't you afraid someone might trip heading for the steps and impale themselves on those ends?
